We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hi,
I am developing for the 54l15 using nrf connect version 2025.5.92 Last Updated 2025-05-15, 10:08:43 and it's starting to seriously frustrate me.
The nRF Connecot for...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
When doing the scan of all possible Bluetooth devices on nRF Connect for Mobile, our custom manufactured Bluetooth wearables are not consistently being found. When by chance...
Hallo.
I am working with Thingy.91x and after learning almost all lessons with Nordic Dev Academy, LTE fundamentals, i have encountered an issue.
Right now I can't use...
Hi，
In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
I am adding OTA support using mcuboot with mcumgr on a custom nrf54l15 board with the upgrade (mcuboot_secondary) partition on an external SPI nor flash (not QSPI). I am using...
Hi,
how to convert/format NCELL data to data that you can use to find the cell on a cellmapper.
This is a ncell result: %NCELLMEAS: 0, “06223A0C”, “20610”, “5334”,65535...
Hi,
I am currently working on making it possible to connect with different devices sequentially. It was told to me that it is possible to first scan all devices, and then...
hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hi,
Our project need 7 seperate PWM outputs, as the nRF52840 have 4 hardware pwm, I decide to use GPIOTE with PPI to create extra 3 pwm outputs to drive Red/Green/Blue...
Hello,I tryed to install the CMSIS Wirzard in SES on the video from https://www.youtube.com/watch?v=b0MxWaAjMco But it deosn't work. I don't know why. I did read the DevZone...
Hey,
I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0.
According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
While testing CoAP with NB-IoT I normally get PSM (sleep) delay = 20s before PSM mode is set (0.5mA with UART enabled), but after awhile PSM delay increases to ~4.5min (at...
Hi,
I recently added FOTA support on my project which runs on nRF5340 + nRF7002. I am currently working on a devboard, nRF7002DK.
Previously, I was running the project...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
Hello,
Currently the nrf-connect extension offers board targets under build configuration. These are categorized as "Nordic SoC", "Custom boards", "All". As I have understood...
