There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
In my application with nRF5340 and nrf connect sdk 2.3.0 which works well as Peripheral, if I activate CONFIG_DM_MODULE=y I always get the error "...ld.exe: region `RAM' overflowed...
I had an opportunity, to do a complete pristine reinstall of Windows 10, and to then do a pristine install of Visual Code, nrf connect, etc.
After doing that I did this...
Hi,
I am working on a project where we need to connect to multiple peripherals which also include mobile devices. (up-to 10) on BLE central.
We need to measure the distance...
HI,
I find that the vs code always loading something as below, the Kconfig has some empty.conf, and can't create new Projects.
Then I return it to V2024.9.87, It works...
Hello, guys
We want to evaluate nRF9151 SiP the following way:
To set it to operate in serial mode in which it is ready to receive AT commands (it comes pre-flashed...
Hi,
I've been developing a Matter device based on the nRF5340 SoC, and have been using the DK up until now. We've been developing a custom board in parallel. I've created...
I have nRF Connect SDK v2.6.1 installed on a Mac, the latest toolchain installed via nRF Connect for Desktop, and VSCode with all the nRF extensions. Everything works pretty...
Hello,
I have a custom hardware, with an external 128MB QSPI flash memory connected to a nRF5340. My current task at hand, is to store firmware update images for MCUBoot...
If I am having a custom board created and assembled using a pcb maker (makerpcb, jlcpcb, or pcbway) what do I need to ensure is on the board so I can flash and debug it? I...
We have a issue about nRF9161 on our custom board.
we flash hex our board. It doesn't work very well. sometimess it work and consume about 90mA current. sometimes board...
In our project we use a SHT4x sensor connected to I2C bus of nRF5340. To lower power consumption during idle/sleep we've a power line switch to disconnect the SHT4x from the...
Hi Nordic team,
I was testing whether Zephyr's LLEXT would work on the nRF52840DK. The example can be compiled on NCS 2.7.0 and loads fine. However the final step of having...
I am working w/ the nRF5340DK, and the project mentioned here (NCS v2.5.0, nrf/samples/crypto/rng). I was able to build/flash the project.
I wanted to verify whether the...
Hi,
I am getting to grips with the device tree and when i add an over lay file to the project, the 'new' devices are flagged with the waring that theyre being over ridden...
