There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
I have some pdf for AT Commands with DECT-NR+ and I found this article: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/libraries/modem/at_shell.html
Basically...
Hello everyone, I took the example code "ble_app_hrs" and added a pin toggle to verify that the code is loaded correctly onto my custom board, which is programmed via the...
I'm trying to install the toolchain manager on a new work computer and I'm running into issues that I think are related to my work's proxy.
I've tried following the steps...
I am trying to configure the STS4x temperature sensor by Sensirion on I2C on a nRF5340DK, I have setup my the coding exactly how sensirion suggested except few changes such...
Hi,
When I try nrfsdk/zephyr/sample/bluetooth/periodic_adv_conn. I notice that the max subevent data size is about 64bytes. If I send a data size larger, I will get a error...
Hi DevZone,
I have made a custom PCB with the nRF52832. I placed the same coaxial connector that is on the nRF52 DK in my PCB. At this point, I want to test the BLE functionalities...
Hi,
I am unable to build the MQTT over Wi-Fi lesson 4, exercise 1 using the nrf7002dk_nrf5340_cpuapp board configuration, but the same code builds successfully with nrf7002dk_nrf5340_cpuapp_ns...
Greetings all, Does the Direct Test Mode (DTM) app v2.4.1 provided in the NRF Connect for Desktop v5.0.2 package support gain settings for the nRF21540 FEM such as +10, or...
I am working on nrf52840 and I want to control the motor speed so I want to generate the variable frequency PWM for the same. How can I generate the variable frequency PWM...
Hello,
I need to configure second UART for nRF52840 DK. So I would like to know the overlay file for uart2 configuration with exact GPIO pins. Also the .c file to initialize...
I 'm porting code from Zepyr 3 .5 to 3 .7 and am having errors in my ds2484 1 -wire device . It was working fine but now reports an init error unless I add deferred -init...
L.S.,
I'm trying to build an "Arduino" port for the nrf52840 (Seeed board).
When building an example I'm getting the following errors during the link phase:
.\Objects...
Hello,
In my project I have b0, mcuboot and an app. My nRF SDK version is v2.7.0.
My project works fine if I use an absolute address in SB_CONFIG_BOOT_SIGNATURE_KEY_FILE...
