Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
Hello,
I am developing a device with a nrf52 using s140 with the last sdk. The objective is to interact through ble with other devices that have different custom services...
I'm porting a bluetooth app developed on a PCA10040 to a prototype PCB with a Fanstel BT840F.
My development environment is
Windows 10
nRF Connect V3.7.1
Toolchain...
Hi I have create a firmware to exchange sensor data through UART / RS485 (MODBUS Slave).
I succeeded to create my firmware and test it with a USD Serial to RS485 device...
Running lwM2M_client routine into PSM with nRF9160 is about 450uA current， RTT is used for logging and all UART is disable.
I use ncs1.6.0.
What's causing 450ua?
How...
dear simon
First of all, thank you very much for your help，Now in my program, I also encountered such a problem，I use NRF_ qspi_ Nor the power consumption of my whole system...
Hi
I configure two IO output PWM, one of which outputs PWM all the time, and the other turns on PWM by timer intermittently ，The period of the former becomes wider，As shown...
I’m not able to connect my Thingy91 to the network. I have successfully registered my Ibasis SIM card in the nRF Cloud (or at least that is what I think I have done):
...
Hi,
I am trying to configure a basic output pin in the device tree configuration. I read somewhere a 'compatible' parameter is requires because it describes what will be...
hi team,
Intial we followed this link for system on --> https://embeddedcentric.com/lesson-14-nrf5x-power-management-tutorial/
Now we are trying to enable the constant...
Hai
I have an NRF52840 Development board with 1MB of flash. I have an requirement to store a large amount of data in a flash around 6k samples in one record.
For this...
Hello,
Im using E73-2G4M08S1C module based on nrf52840. Somehow even when in erased state its consuming a lot of energy and starts heating very fast.
Im trying to figure...
Hi Nordic team
I failed to demostarte multicell location sample.
Hardware: Thingy91
SDK: v1.6.0/multicell location
Modem: v1.3.0
Q1. At prj.conf, nrf cloud location...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
Hi,
My application is currently using s132 v5.1.0. The Release notes for s132 v6.0.0 say:
"Fixed an issue where incorrect timing calculations during the LE Data Length...
Hello
I am running this version of SES
SEGGER Embedded Studio for ARM
Release 5.34a Build 2021011401.44914
Nordic Edition
Windows x64
When I run my program in...
