There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
I'm developing on the nRF52 DK which has the nRF52832 chip.
I have a small vibration motor which I'd like to control on/off through one of the boards GPIO pins. At...
Hi,
I'm trying to modify the light bulb example and turn it into a light switch (not a light switch that controls another bulb in the network), but I'm quite new on the...
Hi,
I've noticed that there was an issue with ble_nus in SDK 15.3 - detailed in this post .
I'm using SDK 17, and in my application, I don't check data_handler != NULL...
Hi. I am using nrf52840 with Softdevice 16.0.0.
I set the maximum size to 247 bytes. But I probably only need 68 bytes per packet.
Should I reduce my MTU size to 71 or...
Hi everybody!
I'm currently working on some firmware updates for a motion sensor. The code was originally developed with SDK15.0. The setup is as following:
NRF52840...
Hi,
I was trying with the aws_fota sample, I follow the instruction here and download the app_update.bin with no problem. After it shows completed in 100%, device reboot...
Hi,
I am measuring the time taken between an ANT application sending a message, and a receiving ANT application generating an EVENT_RX. This time is being measured using...
Hi,
my environment:
nrf5340 dk
nrf connect sdk - 1.5.0 version
segger studio IDE
we need a provisioner to add node into the BLE mesh. As per my knowledge, we...
Hi,
I have a few questions about how the peer list works. (using S132 v 7.0.1 and SDK version 16)
How or when are peers added to the peer list of the Central? Are they...
Hi Experts, I have a short quastion, what is the minimal RX-RX turnaround time of nRF5340? Unfortunately this parameter is not available in the specification any more. For...
Hi , i try to translate the arduino library using this URL github.com/.../src
to manipulate the spo2 oxygen concentrator value using the max30105 sensor I try to configure...
When I set tx_power and paired with the following microcontrollers, the power consumption of the 4dbm setting became larger than that of the 0dbm setting. Is this an effect...
Hi,
I am currently working on SDK 15.2.0 on my NRF52840 DK to program a bootloader that can do DFUs over SPI. I have been following the protocol found in this link . I have...
