hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I'm experiencing issues testing the FOTA over BLE on nrf54L15dk using the SMP server sample of the NCS v2.8.0.
To reproduce my issue, just build the sample out...
Sorry if this is documented somewhere, but there is a dot pattern that seems like a QR code on the 9160's exterior metal case. For the purposes of provisioning a product,...
I performed OTA over BLE for Matter samples available in NCS. After OTA performed successfully, it erased the Matter commissioning data and uncommissioning the device. How...
Hello!
I am working on a project based on NRF52832 MCU and NRC connect SDK in VS Code.
I have a custom PCB and I use GPIO pins to switch on the power of the OLED display...
Hello, I am studying DevAcademy Lesson 4 - Data exchange in Bluetooth LE , specifically Exercise 3 using the nRF5340DK . While attempting to build the corresponding Git code...
Hello,
We have a project which requires high accuracy for 14-bit resolution ADC output by using Nordic nrf52832, we regard that the accuracy is linked to the internal...
Hello,
I'm using nrf5340 audio application in nRF Connect SDK v2.7.0.
It has been working normally, but today when I opened folder, the sidebar disappeared, as shown in...
Hello everyone,
I guess my question is more conceptual rather than a specific issue with the code.
I am working on a device featuring an nRF5340 chip and an nRF9160 chip...
Hello, I am trying to get a custom board with an nRF5340 (on a Raytac module) up and running. I want to emulate a simple HID mouse. Therefore, I selected the code from the...
I have just started using 2.7.0 with the nrf54L15 chips and come across a few problems.
When trying to run the UART sample I found that the app overlay files, which I believe...
Other than setting the DCDC_MODE_PIN, what else does the sd_power_dcdc_mode_set() do?
I'm seeing an issue where I have a GPS peripheral on UART that is seeing about 10dB...
Hi Nordic team,
Hi Nordic Team,
We are trying to configure two SPI masters. It works when I use any single SPI (only one), but when I add the second SPI, I encounter...
Hi,
I am trying to compile an old project.
I am using SEGGER_Embedded_Studio_Nordic_v568_win_x64 with nRF5_SDK_17.0.2
I am getting an error message for the following...
Does the 7002 support 802.11 monitor mode? https://en.wikipedia.org/wiki/Monitor_mode
Some chips call it promiscuous mode even though that should be something separate ...
