hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
We are using the NPM1300 with a lithium polymer battery that has integrated cell protection.
When the battery reaches the over-discharge level due to prolonged...
I got the following setup: nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001
nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001...
Hello!
I have a complex issue that I am trying to brainstorm. The task is that I am trying to receive a file over the air and be able to serial flash my STM32U575xx.
...
I have customed my own nrf54l15 board and run peripheral_uart demo successfully. Then I tried to measure its current while running peripheral_uart demo, it was up to almost...
Hi,
I've received the nRF54L15 DevKit and tested the power consumption during sleep Testproject in GIT: https://github.com/marcel-cd/nrf54l15dk-powertest
The result was...
Hi,
I am currently migrating from NCS 2.5.0 to 2.7.0 and running into an issue where the CMakeLists of mcuboot ( https://github.com/nrfconnect/sdk-mcuboot/blob/4c7942e58c5458ce3c4e50d3169e0f865910fe87...
Hi I use nRF52832 and nRF Connect SDK v2.6.1 with visual code
I went through this exercise ( academy.nordicsemi.com/.../) and the FOTA works so far. However, in this example...
Hi nordic:
I would like to inquire about the foundry, packaging, testing, ball-mounting, and process node (e.g. 28nm, 40nm, etc.) for the 52832 chip.
（Writing an internal...
Hello,
I am using VSC on Windows with nRF Connect. Previously I have installed the NCS SDK using the "RF Connect" Toolchain manager.
I have to make changes to some...
Hello,
I'm using my nRF52840 devkit together with nRF Connect for Desktop Bluetooth Low Energy (v4.0.4) app for some testing. The app failed to recognize my devkit. It used...
Hello .
I 'm studying Zephyr .
Is it possible to run a python program in the Zephyr environment ?
I am using Nordic 's nRF5340 SoC and I need certain modules in...
Hello.
I’m new to the Nordic devices and I was tasked to develop a custom board based on the nRF9160 SiP. I took the nRF9160 DK as a reference, changing it according to...
Hi,
1. I was facing issue with my nordic device saying
[02:16:46.206,481] <err> net_pkt: Data buffer (1328) allocation failed. [02:16:46.206,481] <wrn> net_conn: pkt...
Hello. In the developed BLE software, the device uses nRF52840 and uses s140 v7.3.0.
I would like to confirm the s140 nrf52 7.3.0 release notes.
A memory access fault...
I am trying to configure interrupts for two push button (namely upbutton and dnbutton) on a custom board. In the main it is just looping and the module I have is as follows...
