Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I am using a nrf54l10 module on the pcb and using the nrf54l15 dev board. So I have a bootloader, the mcuboot, and then the image. I program over SWD on the pcb. So my problem...
Hello!
What would be the best way to start a custom LE Audio application with a different codec?
I mainly want to evaluate being able to stream 2-4 channels from a 53...
Hi,
I am using the npm2100 as a power management chip in my product, utilizing only the boost function. When only the npm2100 is soldered on the PCB with no load connected...
I am using nPM1300 MIKROE Click with ESP32 over I2C and enter ship mode by writing the required I2C registers from ESP32 .
Observed Behavior
Ship mode command is sent...
Hi,
I am developing a feature to add remote provisioning support to a BLE Mesh-based network. In the network, a provisioner node receives, via a serial command, the UUID...
Hello,
I am trying to reduce the current on the nRF5340 during the distance measurement (dm) sample for BLE ranging. For current measurement I am using the Power Profiler...
I've been trying to establish the network using Open Thread API.
After enabling the IPv6 by using otIp6IsEnabled , when try to start the joiner using otJoinerStart but it...
Hi,
I've already spent a lot of time on this issue. I develop on a Windows laptop. I need to run unit tests with Twister before committing to our repository. I can't do...
We are using SDK 3.1.1 and nrf52DK with our own Model ID and anti-spoofing key from Google.
When flashing the Locator Tag example to the board, a half sheet notification...
We are developing a battery-powered medical device using nRF9151 with nRF Connect SDK v2.9.0 , where data is transmitted to AWS IoT Core using MQTT over LTE Cat-M . While...
Hey, I'm looking for a solution to encypt the DFU_Application.zip and that the nrf52840 MCU can encrpyt it at runtime. Actually I've read that this not offical supported of...
I’m working on an indoor tracking system based on the Bluetooth LE Channel Sounding (CS) API. My target is to support multiple initiators connected to a single reflector,...
I'm using the DFU bootloader from the nRF5 SDK 15.0.0. To initialise the DFU service from the application the ble_dfu_buttonless_async_svci_init() function from the nRF5 SDK...
Hi,
We're about to make a bunch more of our custom boards based on the nrf5340_audio_dk platform (modified with a stereo codec and some other stuff) with a modified version...
