Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
As far as I understand I should be able to use the nrfutil (6.1.x) on a Rpi 4B to update any of the nordic semi devices nrf5x supporting bluetooth (i my case nrf5340) Will...
I am new on Bluetooth. Currently I am playing with BL5340 development board. I need a firmware to test Bluetooth data transmission latency between two BL5340 modules. Could...
Hello,
I'm running the Asset Tracker V2 NCS 1.7.0 conected to the nRF Cloud. I'm using a Thingy:91 with external GPS antenna.
The GPS position is being correctly aquired...
Hello ,I am starting new development in Nordic environment and my system configuration is intel i3 with 8gb ram.
Still it is way too much slow to open nrf connect for desktop...
Hello everyone,
i want to use the 52810 to write into a SD -card, i use a slightly modified fatfs example.
The problem is, the SD card will not initialize as the p_event...
Hi, I'm trying to implement a sleep mechanism in my app. I based my code on the Power Management Example.
I use a button to put the app to sleep and the same button to wake...
Hi Team,
I am working on a project. It requires nordic chips (slaves) to communicate with msp430 (master). I use the nordic example SPIS as the initial code of the nordic...
My project consists of STM32 + 4G + nrf52833. When the 52833 firmware needs to be updated, the cloud service will send the 52833 firmware to STM32, and then STM32 will send...
Hello all!
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My developmnet board acts as a central whereas my phone as peripheral...
Dear team,
1. I am using the Ble_app_uart example from the SDK.
2. I had received the data successfully from the nrf_connect app.
3. Once the data was received over...
I received my nRF52840-DK (PCA10056) last week and today I was given the task to get started.
I started setup my environment with my preferred choice: Arduino IDE. Unfortunately...
Hi
In the actual test, the power consumption of the chip when scanning is started is 9.5mA,This actual test value is higher than the Iradio_rx0 and Is1 in the PS .What is...
Hi
The customer wants to test the RF transmit power of the nrf9160，whether the AT command can be fixed frequency?Or whether there are special tools to test RF power?
Hi,
I'm trying to migrate bluetooth softdevice to a project contained cli module. I found cli module and softdevice would all create an app timer. The softdevice first created...
Hi,
i using 52840DK 10056, keil5
SDKs\nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\
i got err or as follows ,but the...
