Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi Nordic experts,
Recently, I tested and found that I failed to start the advertisement with NCS 1.7.0 if the length of advertising data is greater than 251 Bytes, for...
Dear sir/madame
Start & stop of advertising and how to prevent automatically restart of advertising in case of a random disconnection or disconnection initiated from the...
Hi,
I've been scowering the SDK dicumentation and DevZone for this information without finding it. My apologies if this has been answered before.
When using the SUPL library...
Hello!
is it possible to execute some code in the section
or do i have to implement some kind of thread logic? or any kind of nonRTOS library?
I come from FreeRTOS development...
Hello,
The Example code is running, but only printF() statements are printing and to the PC terminal program.
The example calls for softdevice build 122.
I "think...
Hello,
I am working with the Thingy91 device and the SDK v1.3.0 asset tracker example (I am not interested in upgrading at the moment). I would like to know how I can save...
I flashed my board with DTM image, assign P0.20 for TX and P022 for RX. Most of the times the DTM application can't communicate with the nRF5340, maybe 1 out of 20 times,...
Hello,
I used to import our current project to segger embedded studio v5.62 from keil so I'm followed these instruction .
All project files are compiled well but problems...
On the nrf52840 module, when I first output to one of the GPIO pins when I load any softdevice ble_peripheral instance I have installed. 10 ms after the VDD pin is energized...
Hi,
I have nRF52840 DK, and PPKI power profiler, I measured peak current mA using PPK on Radio Transmitter, And I found there is a big discrepancy between measure and typical...
Hi Guys,
We are currently working on a mesh sensor network. I have already developed a vendor sensor model (client and server). The client will also work as a gateway and...
I have a couple of questions regarding the nRF52840 internal voltage regulators, specifically REG0. I couldn't find the answers from the datasheet and therefore I hope that...
I started using nRF Connect for VSCode a couple of days ago on one computer and it has been working great. Now I had to switch to a new computer where I had also just briefly...
The first chip silkscreen for 2050ST second chip silkscreen is 2109XN third silkscreen is 2052TJ, transmit power configuration for 8dBm actual test from the chip side, test...
Hi, i'm using STLink V2 for compiling the code, the weaknes of this compiler is you can't see the result debuging or serial print output.
so i'm using USB TTL to see output...
