When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Good day, Nordic staff!
We are working on a product using the FLPR for its intended peripheral-controlling purpose. For us, the best way to send commands to and receive...
Greetings to everybody! There is some question about nRF54L15-DK board measured current consumption. I measure current via the P6 connector, that is, I measure current within...
Hi，
The same hardware and software have been in continuous production for several years without issues. However, the latest batch exhibited abnormally high power consumption...
Hi,
I am developing a small app for the nRF52840 using the SDK V3.1.0 and the Visual studio Code on a PC windows 11.
What I like to do is to be able with the app to change...
Hello,
I'm using the nRF5340 and have configured UART with EasyDMA to receive a variable number of bytes at 307200 baud. Our application has strict timing constraints, so...
To preface:
Board: nRF52840DK
OS: Windows 11
nRF Connect SDK / Toolchain: 2.9.0
VS Code Extensions:
nRF Connect for VS Code: v2025.5.152
nRF Connect for VS...
Hi guys,
I am currently working on a data migration of the settings storage to the external flash.
The problem I am facing is that after an OTA update, the device does...
A project I am working is proposed to have an nrf 5340 connected via UART to Yocto (Thud). Am looking for suggestions on an embedded client that will work with v3.0.0 of the...
We are using this custom baord to check the I2C addresses where the I2C BQ_SCL (P1.00) and BQ_SDA (P1.01) connects to various peripherals. However we are unable to get the...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hi,
I am trying to install nRFconnect SDK and VS Code Windows 10 by following NORDIC Dev Academy lessons.
Encountering following errors while building the following example...
in C:\ncs\v3.0.2\nrf\subsys\bluetooth\services\nus.c
The property of BT_UUID_NUS_TX only declares notify, but the permission declares read. After the nRF Connect app is...
Hello. I'm using the nRF52832DK in a test fixture application.
I need the embedded system to know when either:
- a PC has connected and disconnected to the main USB...
