Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
We are referring " ble-characteristics-a-beginners-tutorial " to create a custom service.
I want to modify security permission from "
BLE_GAP_CONN_SEC_MODE_SET_OPEN" to...
It looks like even with the latest SDK 1.6.0, the full modem firmware pre-validation is turned off.
It looks like this is a modem firmware feature, so it would seem that...
Hi All,
I am new in the Dev Zone and apologize in advance if the question was posted in the incorrect section.
I would like to run the Thingy91 as tracker hardware for...
Is there any API (software) available to evaluate DWM3000EVB module on nRF52 DK?
Can we use the API/software available for nRF52840-DK for nRF52-DK as well?
From where...
I am following https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.0/nrf/gs_installing.html for installing on Linux.
I have installed SES from 1.6.99 documentation...
I am trying to get use the Zephyr console sample for nrf52840dongle but when I have configured the following in my prj.conf file I get a link error.
When I reload the...
Dear friends,
From this case , we already know that the mesh stack will arrange a new block when the node is reset, so we will get a new sequence number. We will use the...
Hi, dear Nordic team. I would like to use buttonless OTA DFU for nRF52805.
Here is what I did:
Step 1) install all tools
Step 2) Build my ADC code, rename the output...
Hello
I'm going to use 'frequency hopping' to prevent frequency interference.
I don't know what frequency hopping is yet. May I have a good example and related documents...
Hi there
We managed to send/receive SMS on the nRF91Dk using the asset_tracker_v1 example, which contains the at_client.
However, with the asset_tracker_v2 we never...
Hi all,
Here's the context -
Hardware :
- nrf52840 DK
- sensor - LIS3DH connected via SPI
Software:
- SES
- nrfConnect
I need to send data being captured...
I've been trying to write a simple I2S loopback project for the nRF5340DK board using SES. Zephyr's documentation doesn't list I2S as a supported peripheral for this device...
I updated the firmware according to the video "https://www.youtube.com/watch?v=xQ7hDzRULJQ&t=314s&ab_channel=NordicSemiconductor"
File for "update modem" : mfw_nrf9160_1...
