Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
hello,
i find a mistake line 62
"ldr r0, =%4 \n" ->>>>> The '=' should be removed .
void app_error_handler(ret_code_t error_code, uint32_t line_num, const uint8_t...
modem fw 1.3.0
ncs 1.5.0 and master
I am trying to test modem firmware upgrades using the lwm2m client sample and every time it is writing the 20% downloaded chunk, the...
Hi, I am following the tutorial and have some questions during the implementation.
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-2-ncs-v1-4-0
A red led...
Hello There,
So basically I need to send and receive and data from to Serial Terminal via FTDI module to nRF9160 DK. So for this I am using ncs\v1.5.1\nrf\samples\peripheral...
Hi.
After updating Programmer of nrfConnect to v1.4.9, I have not be able to "execute Erase All" command.
Error message is "Error: Error occured when program. Errorcode...
Dear Nordic,
how to set UART/USB console output to be non-blocking? We use printk() to output some debug info to USB console. When the USB isn't connected, the program stalls...
Dear Nordic-Support-Team,
I (software developer) work together with an electrical engineer to develop a device, which will incorporate the nRF9160 SiP. The firmware/application...
Dear Nordic Engineer
I currently have a project that requires 5340 to act as an MCU. I also need to plug in a FLASH, which is 4GBIT NAND FLASH. Is there an example of supporting...
Hi :
nRF52832 PCA10040 DK burn this link hex code: https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE/Download#infotabs
Can...
https://devzone.nordicsemi.com/f/nordic-q-a/49269/long-range-nrf52840-central-can-t-connect-with-peripheral-in-ble_gap_phy_coded
due to this problem recently I have problem...
Hi Nordic Support Team,
I have asked this question previously, but I might as well make another post to collect my experience with this problem this past month. I will try...
Hello,
Here is my configuration:
NRF52840
S140
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 247
I would like to enable DDLE in order to get more than 27 bytes in each...
