I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hello,
I am currently using the bt and uart backend for zephyr logging on ncs 2.9.2. I want to be able to save logs to flash which will be useful in debugging/ and be...
I am trying to establish a BLE connection between two nRF52840 devices.
The child devices are properly advertising and are close to each other.
When attempting a BLE connection...
Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
I saw a description about on-the-fly CCM mode decryption in the nRF54L10 datasheet, but the Configuration section of CCM00 states that it does not support on-the-fly decryption...
I would like to know about the Mesh model.
Light Lightness、
Light CTL、
Light HSL Setup、
Light Control
Are there no configuration components for any of the above...
Hey,
To program the nRF54L15 EVK, is there some dedicated program tool needed?
From EVK package ordered online, there is only USB cable inside. Can I assume the USB cable...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Hi I am starting with nRF9160. I build and program "nrf91_simple_tracker," but while running, I got the following terminal output:
I am using nRF Connect SDK v2.7.0 with...
I'm developing a solution using nrF54L15 that needs to receive packets from existing legacy RF devices in the field that cannot be modified.
Required RF Parameters:
...
Hi team,
I am using ncs2.6.1 ( github - install from VS Code ) , toolchain 3.0.2 ( previously used 2.6.1), My DK works great standalone also here is the view from nrf-connect...
Hi,
I am planning to get the PPK2 fabricated and assembled using the HW files available for PPK2.
Just wanted to check will I have issues loading FW on it since I don...
Hi all,
I’m working with an nRF52833 using SDK 2.8 and trying to enable DCDC mode to reduce current consumption.
I tried adding:
CONFIG_BOARD_ENABLE_DCDC=y but I got...
When developing a keyboard peripheral using the nRF5 SDK keyboard example, how can I determine whether the connected host device is a Mac, Windows PC, or Android phone?（NRF52833...
Hi, I am working on a channel sounding trilateration system using an initiator and three reflectors. When I was testing with six reflectors I couldn't help but notice the...
Hi all,
I need to use the SPI3M interface and following various example I implemented the following code on the nRF52840 with SDK 3.0.2
Whenever I configure the SPI to...
