Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
ASSET TRACKER V2 Modem problems:
I have set up asset tracker V2 for nRF9160 and it sends the messages (GPS, Temp, Hum, etc) and the corresponding timestamps, which I can...
Dear friends,
I followed the tutorial( Using serial interface for provisioning and configuration ) control a mesh node.
a) The PyACI as a host via uart connet to 52840...
I'm running NRF Mesh3.1.5 in Android on my Galaxy S10. I'm following the steps in the Bluetooth Mesh Developer Study Guide and can connect to the Switch an Light nodes as...
Hi,
I wanna my appication run first instead of bootloader. Here is my steps:
Create bootloader_setting: nrfutil settings generate --family NRF51 --application application...
Hi,
I have a card with some large capacitors in parallel with the VBAT line. How does the PPK2 work (in source mode) at board start-up where there might be a short in-rush...
I have a question. The sample code I modified is nRF52832\examples\ble_central\ble_app_uart_c. Scanning will be triggered when scan_start() is called. The device has been...
I have change the version of wireshark on windows 10 .(NOW I?M USING THE ONCE OF THE APPLICATION NOTE)
After that i have modify the .bat file because he never see python...
Hi,
My provisioner is a light switch client on a dev kit NRF52832.
Now I want to define it as a proxy node as well but I suspect that my Android App cannot send one generic...
Sorry I'm looking in the AoA.
I See that in zephyr main line there are 2 samples :direction_finding_xonnectionless_rx direction_finding_xonnectionless_ tx..
Hawe I to...
Hi,
I am trying to program new chips. I have made the following connections:
Chip J-Link ------------------------------ Gnd Gnd SWCLK SWCLK SWDIO SWDIO VDDH 5V (External...
Hello:
We have a BLE application on an NRF52840 with SD 140 and SDK 1.5.3. Our device acts as a BLE peripheral with bonding and LESC, and we additionally use block level...
Hi,
We have designed the custom PCB where 32.768 kHz crystal oscillator is required. Some how we have managed the component (MFR PART NO. TF325J32K7680 ) suggested by Nordic...
Hi, I came across a forum post that NRF51 had an issue with noises in SWCLK signal.
For the design, do I need to attach an external pull down resistor in design? If so,...
