Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi Team,
We are using the NRF52840 for our development purpose in BLE peripheral Mode. While connecting to the Central Device we observed the behavior, It is negotiating...
Hello, I want to ask a question. We have a project that needs OTA function. There are two Bluetooth devices A and B.
1. Both A and B are central_and_peripheral
2. A's...
I want to check for an RX timeout after sending a TX.
I am puzzled on how this comes about.
As best I can tell I have enabled TIMER3 for the timeout.
I have created...
I'm trying to create a user defined HCI command for nrf52840 over the Zephyr APIs to be used against Bluez stack on Linux.
I've enabled the CONFIG_BT_HCI_VS_EVT_USER=y....
Hello,
I am trying to accomplish sending a simple ON or OFF command to the coordinator. Is this possible to do?
I have a router device with these Clusters:
It...
I have been converting my TWI calls to be asynchronous by specifying a twi_handler, but my NRF52840 does not sleep during the TWI calls.
I use SDK15.3 and s140 softdevice...
So this is my understanding of the programming process of an external board using the DK.
Pins from table 1 here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk...
Hi,
I want to develop DFU using BLE. I have started with test image given in the example folder.
I have nrf52480 device , using S140 softdevice. I have followed these...
I am unable to see advertisement on the nrfconnect app, when using BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED
However, when using BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as a central and Android device (Bluetooth 4.2) as an advertisement.
During development, I was wondering...
Greetings.
We've been developing a product that uses BLE Mesh. We are currently using the Waveshare nRF52840 Bluetooth 5.0 Evaluation Kit for prototyping purposes. As far...
When I try basic usage of NRF Queue library I'm getting the following error:
Undefined reference to `nrf_queue_write'
SDK version is 15.3.0.
In sdk_config.h I've enabled...
Hi Support,
I have tried setting up my nRF52840 Dongle ( https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF52840-Dongle ) PCA10059 as explained in the steps...
Hi,
I've got the gaming mouse dev kit and I'm stuck trying to get it programmed using my nRF52840-DK. See my hardware connection image below.
If I leave the mouse power...
