Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
I've been searching for a LSM9DS1 driver compatible with the nRF5 SDK >= 14.0 but I couldn't find any which uses the nrf_drv_twi so I started to write my own but it...
Hi All,
I'm working on minimizing power when transmitting a small message between two nRF52832 boards. I'm also trying to maximize range so sensitivity is important.
I...
Please ignore, this is test post. The SES project in Thingy:52 SDK seems to be broken, I get a lot of error trying to compile. What can I do to fix it?
Hello,
I have an application that requires an always running ADC to sample three channels at 4096 Hz. I have successfully adapted my application from the many examples posted...
I am working on Flashing Code into Nordic nRF52832 using SWD Protocol.
We have achieved 80% SWD in communicating and flashed code into Nordic and verified all is working...
I would like to confirm what I'm seeing on my setup trying to measure current with the nRF9160 DK.
I'm using an oscilloscope and am following the instructions in the latest...
If I were to design a product using nRF52840 & Thread. Normally, I would have to certify the product with the thread group and become a member. The thing is: - the product...
Hello,
I am developing a remote device which uses system off mode for idle state. I also have the condition where extra long press of any key that is beyond the long press...
My Peripheral is using the ble_conn_params module. I'm seeing that if my Peripheral calls sd_ble_gap_disconnect() soon after making a connection, the module will sometimes...
To the kind attention of Nordic support team,
I'm studying documentation in https://developer.nordicsemi.com/nRF5_SDK/nRF51_SDK_v5.x.x/doc/5.2.0/html/a00140.html where it...
Recently I check back again into att_mtu_throughput example in SDK 15.2. there seems to have some updates than in previous SDK, and I see this BLE_GATT_EVT_DATA_LENGTH is...
Dear all,
I am using the following peripherals in our product.
1. TWI Sensor
2. BLE
3. APP timer (1. to poll a gpio pin & as RTC)
4. SPI flash
5. 2 Edge sensitive...
Hi,
I am using nrf_queue to store data in queue which is inserted with time based interrupt at several milliseconds. Also same data from queue is fetched at bulk.
I am...
Hi,
I have modify a BLE program from ble_app_uart by using SDK 15.3, but the system will crash when I do following test:
Please find attach file for my code.
Step1...
