There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
I have a root certificate that is used by the popular TLS certificate service Let's Encrypt that fails to parse in NCS 2.6.0 on the nrf9160dk. You can find the certificate...
I am looking for an example 6 layer stackup for the use of the nRF5340 / nRF7002 combo that has been proven producible by pcb manufacturs. The nRF5340-QKAA requires microvias...
Hello, We designed and tested a firmware on the nRF52833-DK board, whith plenty of debug sessions and reprogramming. Then it has been build for our custom board, based on...
Hi all,
i am trying to update the nrf5340 firmware using STM32 as the master controller via UART. i initially tried to upload the .bin file of my project to nrf5340 using...
Hi Nordic Team,
I am working on a project where I am using an XBee module as the Zigbee coordinator in a centralized network and an nRF52840 (running the ZBOSS stack from...
Hi everyone, I have a problem when I configured custom board GPIO UART in NRF54L15. I know that the NRF54L15 have UARTE00, UARTE20-22, UARTE30. I just use 2 GPIO ( UARTE20...
I use the app_gpiote_user_register to set GPIO port 1 pin, but this registers only 32-bit mask, so it can only to setting port 0.
If I want to use the port 1 pin for app_qpiote...
Hi!
I'm attempting to run the application from this URL , but nothing appears on the serial console, and I don't see any posts on the toilet website.
Could you help me...
Hi,
I am using an nrf5340DK + nrf7002EK. i am able to run an example helloworld application with an immutable bootloader and mcuboot as platform bootloader. When i try to...
Hello! Recently while performing a BLE firmware update using the mcuMgr Library, the stages of the firmware update are as follows VALIDATE, RESET, and fail on UPLOAD. When...
the code below successfully complies and returns 3 services with 1 characteristic each, I have copied the uuid for the primary services and characteristic and that doesn't...
Our board is based on nRF52833, using SDK 2.1.2, Zephyr 3.1.99 Project is configured to enter low power mode for both CPU and peripherals CONFIG_PM=y CONFIG_PM_DEVICE=y Our...
Hi,
After downloading any of the projects from nordic github, how does one compile the project successfully? Where should i extract the files to and what paths should i...
