Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
I'm attempting to initialise my first zephyr project using the nRF SDK, and have been following the academy course on the nRF boards. Problems arise on the install SDK (2...
Hi,
Only the TX and RX of NRF52840 chip UART are used to test OpenThread CLI Demo. How can I change the configuration of UART in the original CLI Demo?
Thanks.
Hi,
"In a BLE Mesh network, if a client uses GAP attributes to send data, can it also use the GATT profile to communicate with a single device? For example, can the client...
I am currently using SDK 17.1.0 to implement dual UART mode on the nRF52833. UART0 is used for logging, and it directly utilizes the SDK library without any modifications...
I use SDK v.2.6.1. To avoid other possible factors affecting the results, I only keep the simplest function in the code which is reading the potential of gpio every second...
In the pairing process among 1 Central and 2 Peripherals
Sometimes the Pairing processing rarely does not work correctly and the following log output:
<err> cis_gateway...
Hello,
We would like to inquire about a technical issue regarding the nRF7002 + nrf5340 with sdk v2.7.0. We have a nrf7002 module connected with nrf5340 through qspi interface...
Hi Support Team
I want to install ZAP tool for NCS V2.8.0 that for Matter development. The command I use to install is pip3 install -r E:/ncs/v2.8.0/modules/lib/matter/scripts...
Hello ：
1.
There is VAMP_IN_XO_LOW in the link, is there VAMP_IN_XO_High （Introduction of relevant information）?
That is, what is the voltage peak-peak requirement...
Hi I am using nRF5 SDK 17.1.0.
Hi I am trying to integrate ANCS in ble_app_uart example. In this example, I am not using bsp library as it is for my custom board.
I am...
Hello Nordic community,
I am facing an issue with flashing the nRF54L15 blinky project to the DK using vscode in Windows 11.
It looks like the compatibility issue between...
I am working on interfacing BLE between my nRF52833 device and both a mobile and a PC. The advertising process is functioning correctly; however, the connection is not establishing...
We have successfully developed a Bluetooth-based tag using the nRF52832 controller and are gearing up for bulk production. While the development phase has been completed successfully...
