Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Why are RADIO_MODE_MODE_Ble_LR125Kbit ， RADIO_MODE_MODE_Ble_LR500Kbit and RADIO_MODE_MODE_Ieee802154_250Kbit not supported in the ESB routines? If I want to use these configurations...
Hi,
I'm working on a project where I want two units to be able to wirelessly send packets to each other whenever they need to. Sometimes only one of the two units may be...
If I initialize the IPC and then turn on the bt_enable, it will lead to the status quo in Figure 2, what is the reason?
If I block k_sem_take (&bound_sem, K_FOREVER) and...
We have a working production system that is based on asset_trackerV2. It is working perfectly but there is a random event happening that I can not explain. On every reset...
Hello, I´m working with the SMP server sample, but I need to modify that one for the following feature related to OTA: 1. Update Nordic firmware with the image system of the...
Greetings,
in Visual Studio code the project workspace looks ok. However NRF Connect is not able to see the application. The error message is of no help:
This did...
Hi everyone!
My name is Natalia, and I’m just starting to work with Nordic. This is my first design, and I’m trying to connect the nRF7002 module to the nRF52840 microcontroller...
I need to match the 50 ohm impedance for antenna performance. It would be easier to manufacture using 4 layers, but I'm planning to manufacture it in 2 layers due to cost...
We are working on product to combine esp32(wifi chipset)+nrf52840(ble, thread and matter ) we wants to keep it as matter device + matter controller to have its seprate network...
We are finishing up our certification process and to complete Wifi Adaptivity, we need to operate the Wifi Shell sample . However, we need to do it on top of our custom board...
Hi,
ncs\v2.8.0\nrf\samples\esb
1. Based on this example, how can customers achieve the frequency modulation function 2. What are some examples for reference? 3. What frequency...
I used this direct test mode sample project: "ncs\v2.6.1\nrf\samples\bluetooth\direct_test_mode"
I can connect and test it normally on the nRF5340 development board with...
Hi,
I am currently using the NRF52840 in a 2 MCU setting (2nd MCU is from STM). UART0 is connected to the PC while UART1 is connected to the second MCU for communication...
