Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
My NCS version is 2.6.1, and the modem firmware version is 1.3.6
I found that delta upgrade often fails when testing the firmware of FOTA upgrade modem for 9160. Currently...
Hello. How can I monitor that SoftDevice is working properly? I am trying to monitor using Radio notification, but RADIO Active does not guarantee that the SoftDevice is working...
Hi ,
I am running "Cellular IoT Fundamentals". In Lesson 4, Exercise 1, has MQTT communication. Everything went well up to the point where I have to PUBLISH from MQTT Explorer...
Hello,
I'm new to pretty much all of this, but I'll do my best to explain my issue. As the title says, I'm currently trying to get a LSM6DSO sensor to work with the NRF52832...
Is there a way to avoid duplicate board targets if I have the same repository in two different places on my machine?
Or some way to ignore a workspace path so they're...
I am working on a project using ncs 2.2.0 on the nRF52833DK.
I have a very simple requirement, which is to save an id-data pair in Non-Volatile Storage and be able to change...
I made an example based on the NVS sample code (Connect SDK 2.2.0) which simply reads a value from the storage partition if it exists, then updates it if either it's different...
We have a system with a central device and a peripheral both based on nrf5340. The central device is also a Broadcast source and the peripheral is also a Broadcast sink in...
I’m working with the Audio Application (from the Nordic sample program) on an nRF5340 Audio DK as a gateway, and a custom board with an nRF5340 as a headset. The custom headset...
Hi, I'm running the fatfs sample using an Actinius Icarus board (nrf9160) and a microSD card, connected via SPI. The original sample works as it should (it mounts and opens...
Before setting `CONFIG_USERSPACE=y`, my image size is ~680KB. After setting it, it overflows my partition by ~60KB. The partition size is ~840KB, meaning userspace has added...
Hi,
I am testing the BLE beacon sample on the NRF54L15 PDK, and it was successful as I was able to detect the beacon using the NRF Connect scanner. However, when monitoring...
I am developing the LE Audio feature for nrf5340. My project is based on nrf5340_audio demo, base on NCS 2.7.0. I am not very familiar with sysbuild. In NCS2.4.0, I am able...
Hello.
I want to install the nrfutil on my macBook(pro m1).
https://www.nordicsemi.com/Products/Development-tools/nRF-Util
I downloaded the nrfutil install program...
