hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
We are seeing issues with Segger Systemview Post Mortem Mode. Original issues were revealed on our custom board with SDK 2.6.1. After enabling the feature firmware crashes...
Hello,
I would like to test TX for ltem. I'm using nrf9160. I would like to use: - Band: 1 - Frequency: 1950 MHz - Tx power: 23 dBm - Bandwidth: 5 MHz - Modulation: QPSK...
Hello,
I've recently was checking out the Zigbee Weather Station application running on the Thingy53 and have spotted a weirdly formatted log message regarding temperature...
Hello everyone, recently I received a thingy:91x with an extra truphone sim card.
I am based in Indonesia and want to test the cellular connection from device but doesn...
I built the demo zephyr/samples/bluetooth/hci_usb for my nrf52820, and it worked well.
But when I tried to read its manufacturer name by using command `hciconfig -a`, it...
Hi there,
I want to capture all the logs made by Zephyr and printk() calls. I want to forward these logs via USB using our custom application protocol for debugging purposes...
Hello folks,
I need some help troubleshooting a BLE antenna issue on our custom nRF52840 PCB . Any insights would be greatly appreciated!
Issue:
BLE sometimes advertises...
ncs v2.9.0
nRF52832 DK (NUS central)
nRF52840 DK (NUS peripheral)
1) When connected, see the empty PDU from peripheral to central about 100ms interval.
2) To use...
I'm trying to add an Aquara temperatur sensor to Zigbee shell running as coordinator on a 58233DK.
Regarding the logs in the serial terminal, it looks like the network was...
Hi,
I am using a nRF9161-dk with the nRF7002-ek shield WiFi tracking.
Using the nRF Connect Quick-Start, I downloaded the nRF Cloud Multi-service application and went...
I'm new to Nordic technologies and ML MCUs!
Does the ARM Cortex-M33 core, nRF5340 audio DK devkit, without any other board od periferic, support edge impulse ML? If so...
NCS 2.7.0 nrf52840
I noticed in i2c_nrfx_twim.c there are some calls to pm_device_runtime_get, while in another thread ( thread ) it was mentioned that Nordic is no longer...
Hi,
we have nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin
build for CPURAD
PC: Windows 11 Pro
I'm trying...
NCS 2.9.0
nRF52840-DK
Using the OpenThread CLI example.
After turning on the TCAT function, when using MeshCoP Commissioning, the joiner will experience a system failure...
