Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
HI DEV
Currently we found a UART Frame error on customer product:
Application scenario diagram
Figure1
nrf52820 ,SDK17.02, softdevice:S132 , gap event length=6*1...
Hi! I'm new to zephyr and nRF boards.
I am trying to write a custom board using the nRF52811. When I try to build examples using the custom board using the command (syntax...
When I asked earlier, it was not possible to send HTTPS payloads greater than 2K due to the TLS secure socket buffer size limit. I see in the most recent modem firmware release...
I'm using nrfjprog version: 10.13.0 / JLinkARM.dll version: 7.50a to flash a firmware onto a custom PCB with nRF52840. Programming hardware is a nRF52840 DK. Our firmware...
Hi,
I am sensing interrupts on a pin using GPIOTE. I can see the interrupts coming on the oscilloscope. The firmware also detects the interrupts. However once I am inside...
Is the IXIT for RF of nrf52832 correct bellow? The test house said the value of inband image frequency should 4Mhz.
IXIT for RF
IXIT Reference
Identifier ...
in \nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\zigbee\experimental\cli\cli_agent_router example , we use the nrf52840 dongle as the Coordinator, for joining the...
what happened when I create a kernel timer (based on the 32k RTC) by nrf connect sdk on nrf 52840 dk?
static const struct k_timer my_timer; static const struct k_work my_work;...
Hi All,
Im pretty new to embedded systems and currently trying to connect a TE MS5837 30B pressure sensor to a nRF52840DK (pca10056) which is all being done via Segger ...
Hello,
I am using openocd to flash nRF52 DK, however, I have several devices connected to my pc at once and I can't figure out how to flash just one of them, When a single...
I need to call the API: clock_control_on( const struct device *dev, clock_control_subsys_t sys)
located at the SDK path ncs\v1.6.1\zephyr\drivers\clock_control.
...
Hi, I am communicating SIM808 with nRF52840. I have made changes in libuarte example and send AT commands to send SMS. I have the following question.
How can I know that...
Current I am using nRF52840 Dongle to develop a Bluetooth PC Tool base on nrf_ble_driver_obj_sd_api_v5 which shared on https://github.com/NordicSemiconductor/pc-ble-driver...
