I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I am developing BLE Mesh product with `nRF connect SDK`.
I understand most of sample project has a function of proxy node. But I don't know how to connect a provisioned...
I've upgraded several Thingy91 boards successfully with the latest firmware and have ran into an issue with another Thingy91 that I've purchased. Here is the error when I...
Hi,
I am storing sensor data into flash and sending it to client when it is requested by Indication characteristic.
I don't have any issue with reading/writing/updating...
Hello developer,
I am new here and learning Beacons with the Board nRF52840 Feather from Adafruit as scanner and Segger Embedded Studio. I refer to nRF52 SDK 17.0.2 and...
Hi all,
I have connected my PPK II to my pc (Ubuntu), installed the software and connected the device.
I can't seem to find the mode or start button anywhere on the user...
Hello everyone,
I am using the fanstel BC840, where the tx and rx pins of the uart are alloced on 1.02 and 1.01:
So i have created a custom_board named hello_board...
Hi,
I’m trying to test/confirm the accuracy of the 32kHz crystal oscillator and the 32MHz crystal oscillator by toggling a GPIO at a derived rate and at 50% duty. But I...
The tag options did not include just nRF Connect as an option so I picked something that had nRF Connect in it. This issue has nothing to do with the SDK.
This is a question...
Help me simple LED Blinkink nrf51822 AA type i'm using YJ-14015 and stlink compiler.. i'm also using keil for IDE. i don't know how to create program and setting for compiler...
Hi,
Using nrfutil tool to transfer firmware package on Windows 10 system is much slower than on NRF toolbox on Android phone. How can we improve the transfer rate of nrfutil...
Hello, when trying to program a custom board with an NRF52805 with a J-Link from SEGGER Studio using one of the examples for the board "nrf52dk_nrf52805", I get an error saying...
Dear Devzone,
At the moment, We do not have methods to measure the GPS sensitivity of our products based on nRF9160.
We are using an active antenna with LNA gain 16dB...
We are using the NRF52 as a SoC in a sensitive analog application,
I need to model power supply noise created by the DCDC convertors REG0 and REG1.
Is there a SPICE model...
Hi Nordic team,
My dev environment is as follows:
nrf52840 + s140 +SD6.0.0 + SDK15.0.0 + SES + nrf52840-DK
Here, nrf52840-DK is configured as BLE Central and my peripheral...
Hello,
I'm trying to develop a ble-uart gateway based on mesh provisioner and peripheral-uart samples but i'm getting an error on getting the device bind of the uart device...
