Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). SES used Printf as a comment display and output it to the Terminal Emulator. I...
I've previously used Getting Started Assistant to install nRF Connect SDK 1.5.0 on macos and managed to get a complete and functional install.
I'm now trying the new Toolchain...
HI,
I have few queries regarding nRF52805.
Is there any specific pin configuration required to enter nRF52805 in to programming mode?
What is Adverting connectable...
Hello. I am conducting experiments with data transmission via the Enhanced ShockBurst protocol with BMD-340 modules. Transmission parameters: 2 Mbit radio channel speed, 512...
Hello Sirs
I want to use the serial port of nrf5340-Dk to get some serial data from a sensor and transmit this
data Via a peripheral connectable config by nrf5340-Dk ...
I'm trying to access an SD card with FAT_FS, with no success. I hooked an analyser to the SPI, but it's completely dead. I'm using NCS v1.6.0.
Is there something...
I am very new to BLE development, and am building my application on top of the ble_central\ble_app_uart_c example.
I have this tag defined at the start, with the other global...
Dear Nordic Engineers
Our customer uses NRF52810 with a PA chip, the model of the PA chip is RFX2401C. The attachment is the manual of the PA chip. The hardware connection...
Dear Nordic,
We use CONFIG_BT_CTLR_DATA_LENGTH_MAX definition set to 251 in our project to be able to send large data packets. Still, when migrating to nCS 1.6.1, we've...
Hi, Nordic team!
I want use RTC with Prescaler 32765 for generating Tick event with 1s interval. Could you help with calculation of jitter for Tick event in microseconds...
Hi,
I need to reduce the consumption of the peripheral_uart sample on a nrf5340dk, I use nRF Connect SDK V1.5.0.
At the beginning, I measured with an ampere meter 591uA...
When I program my external board via the nrf52dk the programming is much slower then when I program the nrf52 chip on the devboard. Is this normal behaviour and if not how...
Hi,
I'm evaluating a wireless microphone scenario, using 52's I2S and external ADC chip to sample sound signal, and than wirelessly transmitting it to another 52 for receiving...
Hi,
sorry if this is a trivial issue, but I've been strugling with this for a while, so I decided to just ask for help.
For context, I'm trying to create an application...
I have devices within an same group that bind with same app key, all are working normal together. But I want one device to be unbind and bind with another app key(out of the...
