Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
i find a mistake line 62
"ldr r0, =%4 \n" ->>>>> The '=' should be removed .
void app_error_handler(ret_code_t error_code, uint32_t line_num, const uint8_t...
modem fw 1.3.0
ncs 1.5.0 and master
I am trying to test modem firmware upgrades using the lwm2m client sample and every time it is writing the 20% downloaded chunk, the...
Hi, I am following the tutorial and have some questions during the implementation.
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-2-ncs-v1-4-0
A red led...
Hello There,
So basically I need to send and receive and data from to Serial Terminal via FTDI module to nRF9160 DK. So for this I am using ncs\v1.5.1\nrf\samples\peripheral...
Hi.
After updating Programmer of nrfConnect to v1.4.9, I have not be able to "execute Erase All" command.
Error message is "Error: Error occured when program. Errorcode...
Dear Nordic,
how to set UART/USB console output to be non-blocking? We use printk() to output some debug info to USB console. When the USB isn't connected, the program stalls...
Dear Nordic-Support-Team,
I (software developer) work together with an electrical engineer to develop a device, which will incorporate the nRF9160 SiP. The firmware/application...
Dear Nordic Engineer
I currently have a project that requires 5340 to act as an MCU. I also need to plug in a FLASH, which is 4GBIT NAND FLASH. Is there an example of supporting...
Hi :
nRF52832 PCA10040 DK burn this link hex code: https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE/Download#infotabs
Can...
https://devzone.nordicsemi.com/f/nordic-q-a/49269/long-range-nrf52840-central-can-t-connect-with-peripheral-in-ble_gap_phy_coded
due to this problem recently I have problem...
Hi Nordic Support Team,
I have asked this question previously, but I might as well make another post to collect my experience with this problem this past month. I will try...
Hello,
Here is my configuration:
NRF52840
S140
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 247
I would like to enable DDLE in order to get more than 27 bytes in each...
