hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
Just a small question, as the subject indicates: Is the power consumption for the Radio RX component (per µs) indicated in the Online Power Profiler for connectable...
Every time I try to connect to Android phone (running Android 7) or nrfConnect, it connects the first time. After I restart the nrf52 DK, the host takes a while to reconnect...
Dear Nordic support,
Now, I am using Nrf51822 to build up BLE Mesh network in my project on Keil C. As I found in here, Nordic doesnt support this chip anymore but is there...
When I try to receive data from terminal at that time it can not goes in uart_error_handle() function and data is not received.
Which macros are enabled in sdk_config.h...
As regards the NRF52840, I want to make sure that it is in System Off not Emulated System Off. Hence the device must not be in Debug Interface mode .
I want to retain the...
We're developing a low power communication stack, where every uA counts.
Currently, I have the system running at a few uA higher than expected, which I'm trying to track...
Hi,
We are developping an app using nrf52840. We started with the SDK14.2 and needed to migrate to SDK15.0 in order to use the long range. We are also using a Bootloader...
hi,
i am trying to on/off led on board(light_bulb code) which is controlled by the other board(light_switch code) with a gpio. when gpio is high led should be on and when...
I am using a NRF52832 and i want to burn a HEX bootloader that only jumps to my APP (i have already burned the Softdevice) when i reset it...
Can you help me ?
Hi,
I am trying to get the GPS from my thingy91, but it is not working. I can see that the board has CAT-M1 connection when I press the top button to get the GPS signal...
Hello!
I am trying to upload my compiled code via nRF Connect v2.6.2 to my nRF52832. But in nRF and also in J-Link RTT Viewer v6.46d it doesn't seem to connect properly...
Hello, I'm developing a BLE peripheral + Zigbee Coordinator, starting from ble_zigbee_dynamic_template of nRF5 SDK for Thread and Zigbee v3.1.0. Both applications (BLE and...
Hi,
After using the ibasis data available on the sim card:
- what is the cost per MB of data consumed on the ibasis provider, please ?
- After using the data available...
