There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi Guys,
I am using Si7021 I2C temperature sensor and I want to read the temperature value using nrf52840-DK. I connected the sensor to the 27,26 pin.
I wanted to read...
DK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
I am using a Fanstel BT832X SOC, which has the SKY66112 PA, on a custom PCB. The...
Hello,
I am using UART to receive data on a nRF52840 DK.
I have written some code using the Serial Port Library.
I have attached snippets of the code dealing with the...
Hi,
I'm working on a tone library. I'm using timer2 and ppi channels to generate 50% pwm signal.
It's working fine.
Now i want to add another timer comparison ( timeout...
I am trying to see if there is a way I can generate a multi frequency audio signal without additional hardware. I am talking about something similar to DTMF. The audio wave...
Would you please tell me how to use the nrf52832 PWM interface to implement differential output to spkr?
Here is my PWM interface configuration code:
NRF_PWM0->PSEL...
I am working on a device which also needs to give audio feedback to the user.
The app on the mobile phone needs to send a wav (or similar) file (mono, speech) to the device...
hi, I am using nrf52832 development board for PWM and I want to play an audio (.wav) file using PWM, I am unable to play the audio clip using the PWM, and same audio file...
Hello,
I'm using SDK15.3 and trying to do a non-connectable advertising while connected.
For that I set my adv package as non-connectable, however, when I run the function...
Dear Nordic Team,
I have a BLE application that we developed on nRF52840 DK for S140 based SoC and this application is working fine on the DK Board.
Now we would like...
I am using IAR version 8.30.2 . When I try to build the example project is the nRF5_SDK_15.3.0_59ac345 for 802.15.4 for the wireless UART I get a build error:
wchar_t in...
When I start my nRF9160 modem (AT+CFUN=1) it can sit in CEREG mode 4 (unknown) for a couple of minutes, before it switches to 2 (searching) then 1 (registered).
Is that...
Hi
I am trying to implement UART on nrf52832 , s132 central and peripheral code.I am getting the following error.
Description Resource Path Location Type fatal error:...
