Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello, is there a way to send messages via the mesh transport/access layer (not using client/server models) but still be Bluetooth SIG compliant? where can I find information...
Hello,
There are a few posts about EasyDMA consuming 1-2mA of current, and I've measured similar currents. In the nRF52832 product specification, this appears to be one...
Hello,
I am running the ble_app_beacon example and want to add battery percentage in the advertising packets, how to do that. And is it possible for ble_app_beacon example...
I had planned on using the nRF52840 I2S peripheral in Nordic Master mode to either produce a 31.25 kHz sampling rate, or a 62.5 kHz sampling rate for my application.
There...
How do I make my phone to auto connect to my nrf51822 device when it is within range ? I dont want to keep having to tap connect on my app. (android and IOS)
I started with the ble_app_template and a preexisting project written with sdk 12.
I have a custom service and 2 characteristics.
The point I am at now is that my DK advertises...
Hi,
I am doing a beacon application. I am advertising sensor data. I am facing issue with advertising.
When I am powering the hardware using usb cable, my device is working...
Hi,
I am trying to interface external flash with the nrf52. I am able to read the device id. After writing to the status - configuration - bank address registers, I am...
I'm finding a good topic for my thesis which come in the next semester. Has TSCH for nRF52DK be implemented on Contiki OS? If not yet, I want to implement this. It is easily...
I try multiple pins set. My pro code is here.
But this is not clear. I want to decrease my code line. Then I tried this.
I want to know where is my mistake?
I am trying to create a TDMA based network with the nRF24LU1+. I understand that nRF51 and nRF52 have the ability to trigger the transmission of a radio packet upon timer...
I'm using an nRF52 (PRX) to communicate with with an nRF24L01+ (PTX) using ESB. As part of a pairing routine they need to switch channel and addresses. I've confirmed that...
I have been working on this for very long time but I can't figure it out, I am trying to use pc-ble-driver to connect my Ubuntu/Raspberry pi to by BT832X module over UART...
