Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...
Hello everyone,
I'm having an issue with my nRF52840 Dongle. I can detect the device with nrfutil device list command, which shows:
> nrfutil device list DC1D9FD62EC5...
Hello Team,
I am trying to change the Lesson 9 Exercise 5 nrf5340_both_sol sample to use internal flash for FOTA. The code builds successfully. I have changed the pm_static...
Hi ,
I would like to use an external GPS active antenna on the nRF9151 EVB for testing (J2), does it disconnect the on board antenna GPS ? should I connect/disconnect any...
Trying to install NRF Command Line Tools. Platform is Linux 64bit x86 (distribution Ubuntu 22). I already have installed utilities by Segger, which may be the reason why NRF...
Question 1: I am using GPIO external interrupt. Does this interrupt belong to GPIOTE PORT EVENT by default? Question 2: How to configure low precision GPIOTE? Question 3:...
I use NCS2.5.0，and I noticed that there are two files(bluetooth.h and scan.h) can help to set scan parameters.Is there any difference betwen these two files?Can I call the...
Suddenly DFU OTA fails most of the time while trying to update units with code & "not secure" bootloader that has been working for years. The FW upload stops at 2% to 8% but...
Hi,
This is my first time designing RF section for BLE using nRF54l15, and i was wondering if you guys can give me some feedback on hardware design. I chose a Johanson 2450AT42B100...
Hi,
I am trying to optimize my nrf52840 application for power consumption. If I run simple loop using nrf5 SDK i get ~1.2mA. However with similiar code on Zephyr: I get...
Hi,
I am developing a small beacon application using the nRF 52805 device, and the intent is that it will send advertising packets at a slow rate, to indicate to a partner...
I'm working on implementing arithmetic operations using the PKA engine on the nrf52840 in Rust, following the CRYPTOCELL — Arm TrustZone CryptoCell 310 datasheet. While I...
Hello all,
I have been working on the implementation of the PKA engine on CC310, and have been encountering some unexpected behaviours when using the modular multiplication...
Hi,Nordic team
I am programming with nrf52833,ncs v2.9.0,base on peripheral_hids_keyboards and central_hids.
On central I call bt_hogp_rep_write_wo_rsp can only send one...
