Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
i am trying to run advertising.py from pc-ble-driver-py .
i am keep getting exception from
except IndexError : raise NordicSemiException( 'board not found' ) is there...
I am looking through the BLE examples, but I can't seem to find an example that best fits my project scope where I wish to have a BLE central service that reads data from...
Hello Nordic support team I want to send command from hm10 ble chip to Nrf52832 dk board.So before I start to implement this I want to know that HM10 ble chip can communicate...
Hi, all.
I want data read from gyro sensor through i2c, and then send it through bluetooth equipment.(PC or iPhone and so on)
But i don'k know how to send gyro sensor...
I am asking about using the sd_rand_application_vector_get function; it seems that it causes my board to crash, and it never returns a success code.
I have already seen...
Hello:
I am upgrading my application to use Mesh SDK 3.0.0 (I was at 2.1.1). In my application, I process the mesh from the main loop (per the instruction in the Interrupt...
Hello All, I would like to implement tracking over MESH network using nRF52840. 1. In my MESH network, there are some devices who continuously advertising (say beacon). 2...
HI.
I am following the document http://infocenter.nordicsemi.com/pdf/nRFConnect_BLE_User_Guide_v2.2.pdf to work with nRFConnect desktop App and my DK BMD300(Rigado). ...
Hello,
I'm trying to play voice using PWM in nRF51822.
I've already experienced this using other MCU before.
So. I'm trying.
Voice source data is 8bit / 8K / mono...
Hi,
I am working on nrf52832 , SDK15 and softdevice S132. I am modifying the ble_app_hrs example code in SDK
I was trying to implement a whitelist with the address of...
I am using ble_app_uart SDK_11 s130 on nRF51-dk. I would like to make the device running on ble_app_uart connectable but not discoverable. The Android app will have pre-knowledge...
I am using nRF52840 with sdk 15.0 version. I am able to read OR write data into flash using fds library. But now i want to write one or two bytes into flash and read this...
Development Kit - nrf52
SDK Version - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Setup : I am trying to interface an E Paper Display...
