hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I am reading the Thingy 52 euler angle characteristic provided by the motion sensors. How is the euler angle calculated by the Thingy? Does it use raw accelerometer or gyroscope...
I'm using SDK 15.0.0 with the nRF52840 and try to sleep without SoftDevice.
The function sys_sleep_request_ms(uint32_t sleep_time_ms) from sys_sleep.h sent me this interresting...
I'm currently working on an application for Nordic that contains a bootloader and a main application using Embedded Studio. Most of the development will be on the main application...
Hello im trying to send data to mobile application, im using the example on ble_peripheral/ble_app_uart but when i compile the folowing error apears.
inking target: _build...
While writing our nRF5 based application, we have used an app_config.h in our project. This is advised as one of the solutions for updating the configuration of the SDK in...
I am a college engineering student. I currently have the NRF51 Bluetooth beacon along with the dongle I am in need of help uploading my code to the beacon via the dongle....
I have just bought an nRF51 Dongle and want to use it like a normal USB Bluetooth Adapter for my Windows 8.1. I have read the Getting Started Documentation, but there are...
I am struggling measuring time between two events. I thought to use the timer driver and the nrf_drv_timer_capture_get function and start/stop the timer with nrf_drv_timer_enable...
Dear Nordic,
I am try to implement RTC(nrf calendar implementation) in BLE example(SDK 13.0). both are working independently fine but combination of works fails RTC when...
My nrf51 SDK version is like this, nrf51 9.0 softdevice 130 chip:nrf51822_xxAArun ble_central_and_peripheral connectivity example, The nrf51 board is controlled by host MCU...
Hi All, the I/O mapping is correct as per the Ref Eval schematics. We are using a J-Link programmer to program it. The IC is not being detected in NRFgo studio. Can anybody...
Hi,
I was wondering if there is some documentation relating to pairing and bonding.
What BLE events (BLE_GAP_EVT, ???) are to be expected?
What do we need to observe...
I use ble_app_uart（sdk 14.2） + light_switch（mesh1.0.1）
Questions are as follows:
1client + 1server is ok, but in the second server there will be network failure!
log...
Hi,
I'm trying to get the tftp example working from the sdk iot examples. When I try it out following these instructions ( http://infocenter.nordicsemi.com/topic/com.nordic...
