I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Product: NRF9160
SDK: 2.6.1
Modem: 1.3.6 My problem is that FOTA download is breaking up more or less every time our device is doing a SW upgrade. We download SW directly...
NCS version : v2.6.1
target board: nrf5340dk_nrf5340_cpuapp_ns
sample project: "ncs\v2.6.1\zephyr\samples\application_development\sysbuild\with_mcuboot"
I use this command...
app and dfu works after I program the merged hex from bootloader_setting, bootloader, softdevice, app using Program application tab, but if I erase chip, reprogram it with...
Hello,
Because i want to connect more than two headset to one gateway, so i modify the prj.conf as follow
CONFIG_AUDIO_DEV =2
CONFIG_BT_MAX_CONN =4
CONFIG_BT_MAX_PAIRED...
Hey all,
Quick question. If we want to send BLE advertisements, beacons, for just 1-2 seconds, then shutdown into SYSTEM_OFF mode, could we initialize the BLE soft device...
I using XIAO nrf52840. https://wiki.seeedstudio.com/XIAO_BLE/
I am developing a BLE peripheral device using the nRF52840. This device is designed to connect with a specific...
Hi,
Could you please advise, am designing a device using the nrf52dk-52832 in nrf sdk connect 2.5.1 and toolchain 2.5.2 that reads the previously adquired samples data from...
Hello,
We decided to use the 802540 battery for our application with the nPM1300. To get a good estimate of the state of charge (SOC), we did the very lengthy battery profiling...
Greetings
I am looking for a conceptual guide to adding my own services to the BLE stack, with Zephyr. Is there any documentation or guide for this? I am working on the...
Hello, I am having an issue with DSP library basicmath where the source file does not seem to be included in the build and I am getting error undefined reference to `zdsp_mult_f32...
Hi,
I am using nrf5340 with v2.5.1 toolchain
I have an out-of-tree driver, where i want to include adc_context.h from and have added:
target_include_directories...
Hi I'm trying estimate the nRF52840s current with the Online Power profiler, the data seemed a bit unclear to me.
I have used the following setting: Chip nFR53840 Voltage...
Hello,
I am trying to do CE, FCC RF test.
I am using nRF52833 and nRF5_SDK_17.0.2_d674dde.
I want DTM to work. DTM is using example source in SDK. What changed in...
I am trying to develop a Consumer Control device. I found the "nrf51_ble_app_hids_kbd_consumercontrol-SDK15" example code on Devzone. But this example code can only do 8 Consumer...
Hi, I have been using nrf52840(my application) and nrf9160(Serial LTE Modem : SLM , which modem firmware was ver1.3.6 and application firmware from switch science )
First...
