Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
We are using nRF9160 as the host MCU and Modem for communicating to server. If VDD_GPIO is powered by 3V external supply and SIM card is powered by VDD_SIM i.e. 1.8V Do we...
Hi,
I have a hex file generated by uVision Keil 5 IDE . I would like to combine this with the hex file form the soft device. These two hex files once combined would help...
Hi,
I would like to change the manufacturing data with time. My advertising_init function implements the following line
init.advdata.p_manuf_specific_data = &manuf_data_response;...
I've been using the nRF52840 DK to load the firmware into my custom nRF52840 board using nRF Connect v2.6.0 and programmer v1.0.2.
However, on another laptop when I install...
Hi,
We have developed a custom board using nrf52832 chip and currently everything like (BLE, TWI, ADC etc) is working fine but we are having issues with the UART. we have...
Hi,
We are using nRF52840 with nRF5 SDK ver 16.0.0 with Softdevice S113 ver 7.0.1.
We use the radio timeslot to implement low level radio comm with very tight timing requirements...
hi i am using this to capture the adc value data_ADC=adc_buffer[1]*(1024+gain_error) / 1024 + offset_error - 0.5; data_ADC_double=data_ADC*3.6/1024; MULTIMETER MEASUREMENT...
When I used nrF52832 mouse application, the SDK version was 15.3. When I connected to MacOS, I had to make several attempts to connect. Can you tell me why?
Thank you very...
Our nRF52832-based board is powered by a coin cell battery, and spikes in current can cause the voltage to drop. This is okay early in the battery's discharge curve, but as...
The communication between the UART peripheral and the nrf52840 works fine until some device connects to the nrf device via BLE. Using a digital logic analyzer I'm able to...
hello
now we want to use nrf52840 qspi interface to connect with fpga. we have a question:whether nrf52840 could be used as qspi slave, and fpga used as master?
if it...
Hello everyone,
I am a beginner with BLE and the nRF52, so I apologize in advance if this question is pretty simplistic. Basically, I am trying to achieve the most data...
Hi, while flashing devices in production testing our customer ran into the following problem. modemFW_flash.py got stuck in an infinite loop, making no progess but consuming...
