Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi
This question is related to sd_ble_gap_keypress_notify() . According to Nordic softdevice S132 v3.0.0 API:-
"This function can only be used when an authentication...
Hi
I am currently working on calculating the AoA. I have 4 nRF52833 DKs and I am using three DKs as transmitters and one as the receiver and the receiver is connected to...
This page https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52840-DK/GetStarted says " If step 4) below fails, you need to re-program the factory example code...
How can I calculate max and average power of this chip? During use, I intend to be at 0dB TX and 1 Mbs data rate with a 3V supply. I am going to guess the max power draw will...
Hello everyone
I am using nRF52 DK PCA10040.
I try to generate puls by Timer 0.
The puls width is 400ns.
This goal was failed.
---------------------------------...
I'm struggling to get buttonless DFU to work with FreeRTOS. I've gotten buttonless DFU sample to run on the hardware. I also have FreeRTOS running on the hardware. However...
Hello,
I need to remap ble bootloader because I want to use nrf52832_AB instead of nrf52832_AA found in dev kits.
I wish I could have this memory mapping in embedded flash...
Viewers! Don't click on a similar issue or you will lose everything you have done!
Calling this method sd_ble_gatts_characteristic_add(...) with a characteristic value...
Dear all,
Im trying to interface LIS3DH with the following code, and drivers of LIS2DH (LIS3DH and LIS2DH have the almost same hardware and config.)
I have included...
It seems there is hardware support for NB2, but the modem firmware isn't there yet.
What's the timeline on this? And if a precise time isn't available, is it in the order...
Hi!
I know, that there are some similar issues in this forum, and I checked them, but I didn't see the clue.
I try to use fstorage to write something to flash. I have...
After many hours of successful LTE connections and using the AF_LTE socket just fine (many creates, many send/receive, many closes), my application now hangs on a call to...
Hi What is the ADC frequency range and operation at nRF52833 ? we are interfacing the TUSS4470 with nRF52833 ,WITH SPI communication . is that the frequency range supports...
In past I try to solve this problem:
https://devzone.nordicsemi.com/f/nordic-q-a/51249/state-chaneged-flags
Now I have new informations about this problem.
Using hardware...
