I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Alright, I'm starting to question my sanity on this one. I am currently trying to use the TWIM driver nrfx_twim.c to access a TWI device. As usual, I did the checks for the...
I am facing an issue about using CMOS battery for NRF52832. I hope this CMOS battery can serve mcu (in low power mode) for at least 1 year. In low power mode, I just want...
I am using a BMD 349 module based on nRF52840.
I am interfacing with AT25SF041 flash memory.
I am using SDK 14.2.
I am writing a byte to a specific address in Flash...
I recently purchased a Thingy:91. Initially it would not connect to the local network. I purchased a a J-Link programmer and via the nRF Connect Programmer updated the modem...
Is it possible to Read the battery status and/or the temperature value from the nRF52810, write that data to on chip memory, and run a code to modify the Major and Minor values...
To the kind attention of Nordic support team,
after some months I gave a look to the segger toolchain configuration for the device host example using the secured gazell...
Hi
I am trying to set up my visual studio to communicate with my nordic device and found that PC-ble-drive can help me with this.
I followed the steps mentioned in the...
HI I'm currently working on measuring distance between two points with two nrf52840 modules with the example "nRF52-ble-long-range-demo" (you can easily find it in github...
I have configured "nrf 52 DK" to worked as BLE sniffer. I am trying to sniff the data packets exchanged between two TI CC 2650 devices (in which one is master and other is...
I am trying to configure my nrf 52 DK board as BLE sniffer. I am following this blog " https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nc_programmer%2FUG%2Fnrf_connect_programmer...
Hi,
I'm using the Light Switch example and would like to read out the own address on a light switch. Is there any application call, such that the stack returns my own...
Hi,
Currently I’m working on a device which is, on the one side connected to a smartphone via BLE and on the other side to another uC via UART.
Therefore, the UART speed...
Hello,
I did a code base on aws_fota sample and added a watchdog, a timer (to feed watchdog) and modified some outputs. Tests about thèses items looks correct.
When my...
Hi,
The Zephyr LwM2M client seems to leak pending objects that are used to track retransmissions. When this happens it enters a loop where the lwm2m_rd_client stops sending...
We noticed strange behavior when measuring voltages with the SAADC with our custom board. When VDD_GPIO is at 1.8V (which is our target), the ADC measurement error is about...
