As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
I open the project :
I want to flash the basic application asset_tracker to my Thingy 91 after I built it from Segger to be sure everything is set and working...
Hi i was trying to add nrf calender part which i found in git hub for nrf52 chip with ble app uart example, but when i nrf_sdh_enable_request() called to initialize ble system...
Hello
I want to install the nRF Connect SDK (v3.4.1) on my Linux Elementary OS 5.1.6 Hera to use the nRF9160 and the Thingy91 later on. I've installed the toolchain and...
Hey,
I am working on S130, nRF51, been working for a long time with DFU and it was fine both using nRF Connect and nRF Toolbox
Lately I changed my workstation and so...
Hello everyone I am trying to program my dongle with the Dk Following this schematic :
When I press the reset button on the dongle, the led start pulsing in red.
I am...
someone that can give me a datasheet of this microcontroller (i think) i searched the hole web and don't find one in specific, the one i found are different in the last line...
Hello, I am working on low power modes of MCU M33 core in nRF9160 SOC.
From the document of nRF9160 product specification v1.0, understood that there are two low power modes...
Hello,
I am trying to capture the advertisements of the surrounding BLE devices with NRF52840 Dongle using pc_ble_driver_py python library. I am successful in capturing...
I am working on third party module RAYTAC MDBT50Q-DB with nRF52840 with SDK V17.0. I am trying to run ble_app_interactive example on it but just can't get it done. I have...
Hello,
I'm using the light_switch example for my application and I've integrated my custom model into it. I want to learn which address the server and client respond/publishes...
Hello,
I want to give user defined hard-coded OOB Number in this example for generic on-off Client-Server code, for provisioning both client and server node ( nrf52 DK ...
Hi,
We use mdbt42v(nrf52832) to design a custom board and we encounter a strange issue.
We use ain2(P0.04) to measure a Variable Resistor value, the code working fine...
Hi,
I am using an NRF52832 device (Peripheral) and I have a requirement to transmit around 4kb of data every 100 ms to a Central.
Can you recommend the correct example...
