hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Dear All,
we're using MDBT50Q in our design and they recommend a 10uF cap while Nordic recommends 4.7uF (Reference Circuit 3).
In terms of power consumption, can anyone...
I activated it and confirmed the network connection in US. Now I brought it to Thailand to test our device, but I could not get the network connection. Can I use a SIM provided...
Hello
I have ported the example project "nrf_crypto_aes_pca10056" to my one project. But now I'm not able to building the project anymore. Segger Embedded Studio will show...
Members
I am in the board design phase of my project. I use Arduino boards (Due & Uno) with SPI. I read that the nRF24L series is not recommended for future projects....
Hi,
So I am using nRF51822 chip to develop our products. We have two motors attacked to our PCB and we want to control the pulse with low power PWM. We want to control...
Hi...
i want to read the data from another board using serial uart .. how to write the command to check the data is available ... in arduino i written like this how to write...
Hello,
I used to use two nRF52810 for testing.
Using Timeslot (BLE+ESB), one of the 52810 paired mobile phones Bluetooth simultaneously sends the ESB.
Another 52810...
What are all the configuration options necessary to configure the nRF9160 as a SPI slave? I'm working with a custom board and have specific DTS files I'm working with. Here...
Hi Nordic Team,
I'm quite confused and can't find a concrete answer so far on the forum, if it is a MUST to kick-off a certification at the Bluetooth SIG Group or not, if...
nRF52840 SDK 15.2
I want to control the power of sensor, so I configurate the pin like this:
nrf_gpio_cfg(AFE4403_PIN_PWR_EN, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_DISCONNECT...
HI,
I am using ".\nRF5_SDK_15.3.0_59ac345\examples\peripheral\wdt" to test “watch dog timer function.
My use case is:
1. If the program is not execute over following...
I have developed ble periphleral device to send 20byte long at every five seconds to the central. Because connecting to serial to PC, I didn't realize the device cannot not...
Hi,
I need to run RTC simultaneously with Softdevice without external low frequency clock source (32.768kHz oscillator).
I used following settings to setup RTC,
RTC_ENABLED...
