Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Does nRF51822 support uart over ble profile? I see in previous discussion "nRF8001 UART-over-BLE" talking about this and answer suggest 51 serial has this?
We want add MQTT...
Hi everyone.
I have problem with my device. I use Visual studio with visual GDB and I'm trying to use interrupts from RTC. Got from this site lot of examples and wrote some...
Hi,
I am running my nRF9160 DK in "nRF Only Mode" (Via SW1). I would like to drive the serial terminal out via one of the GPIO pins, connected to my MAC using an FTDI serial...
SDK v15.2.0 using peripheral spi example. Windows 8.1, uploading to nRF52 DK.
In my while loop I use bma_spi_read() twice with a small delay in between. The first...
Hi,
I am using the reliable message communication to measure Round-trip time based on the Light switch example.
I noticed that in high traffics, some packets are not...
I want to use TimeSlot API for nrf52832.
two question.
I want to use time slots regularly . I call follow, timeslot_open() timeslot_request() - timeslot_end() -> IDLE_STATE...
Hi there,
I've already asked about it https://devzone.nordicsemi.com/f/nordic-q-a/49701/commissioner-disable and I've tried it but nothing work. I've already spent 5 days...
I am in pre production with the nRF52840. My customers have access to the micro USB port on the device. I want them to be able to define a string for the nRF5 transmitted...
I am using nRF51, SD 130 1.0 and SDK 10.0.0. I have 11 buttons connected to nRF. Currently it only works for up to 4 buttons (APP_TIMER_OP_QUEUE_SIZE is 4, but I'm not sure...
Hi,
i am working on spi master example in nrf52832, when clock is set to 8MHz, clk signal output at the nrf52 pin is more like triangle wave.
is there any way to set pin...
Hi,
At the moment, my current location does not have an NB-IoT network for the nRF9160 DK to attach to. This means that the device is unable to activate PSM mode (which...
Working with SDK 15 on an nRF52832:
I have a peripheral applicatin where I'm computing the value of a BLE read on the fly.
Currently I do that by:
Setting up a BLE...
Dear dev community,
I've got a very simple question: How can I see the subscription and publishing addresses list in any mesh node for any model?
Thank you!
Regards...
Hi I am developing a custom PCB for the nrf51822 chip. I heard the nrf51822 chips do not come with preloaded firmware or bootloader. Do I need to also flash the bootloader...
Base on nRF5_SDK_15.3.0_59ac345 for NRF52810, I wrote the following codes,
Use nrf_drv_uart_tx to send data is successful, and NRF_DRV_UART_EVT_TX_DONE occur normally...
