Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
I want to use the external flash on the nRF5340 DK using SPI as the board I'm developing for will not have QSPI. I used the littlefs sample which has a lot of the settings...
Hi,
I'm trying to implement a PRE_KERNEL1 timer (with top priority 0 ) to toggle an LED.
I’m able to control the LED using registers, and now I want to add a timer layer...
I want to send a custom message using a custom Property ID in Mesh Sensor observer example. How do I add a custom Property ID? Currently, I am using #define CUSTOM_ID 0x1234...
I am debugging an application on a nRF5340 DK using nRF Connect SDK from VS Code. (Toolchain/nRF Connect SDK v2.9.0), everything up-to-date.
The build is "optimized for...
nRF52840, nRFSDK 17.0.2, SoftDevice S140 v7.2.0
Hello! We're turning on SoftDevice and using the PA/LNA pin control to drive our FEM. Then, we disable SoftDevice and issue...
Hi,
I found a bug in the init part of the LIS2DU12 driver. The driver tries to reboot the LIS2DU12 sensor using the SW_RESET bit in CTRL1 register even if it is not in...
Hi,
I'm trying to synchronize a process using an nRF52833 dev kit using a Zephyr event.
The code looks like this:
The first routine sends an event and the second captures...
I am working on an nRF52-based device using nRF Connect SDK (NCS) version 2.7.0. The device is configured to enter deep sleep every 60 seconds and wake up via a GPIO interrupt...
Hi,
I'm using the nRF Cloud multi-service application on my Thingy:91X.
I am using the Serial Terminal to see what networks are available, but when I go to attach manually...
Hello,
I've been working on a project using nRF52832 + NCS 2.1.1 including BLE and some sensors : MAX86150, MAX30205, MP34DT05, LIS3DH
I'm sending data of these sensors...
Hello! What are the steps I need to take to switch from BLE protocol to lets say the Gazelle protocol? Is it as simple as disabling the Softdevice? If such a function exists...
We are finishing up development of our product and looking into creating our Bluetooth listing. We are using the NRF52840 SoC (Fanstel BT840F model) with softdevice and NRF...
The NORDIC tutorials are great for demonstrating how to use GPIOs to drive LEDs and read buttons.
However, I need an 8-bit bus to exchange bytes with an external display...
Hi,
I am working on an application using the nRF52840 with the Quectel BG96 modem. I can successfully communicate with an insecure MQTT broker using the BG96 modem. Now...
Hi!
I'm making a new board using nrf54l15 and I found the following issue:
/* * PWM signal can be exposed on GPIO pin only within same domain. * There is only one domain...
