Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I am trying to program my nRF9160 DK v0.9.0 with mfw v1.1.4 but I am getting an error "Modem DFU failed with error: Error: Error occured when program. Errorcode:...
Greetings,
I have two nRF52840's where one is modeled as a peripheral and the other as a central. I have created a custom service and characteristics on the peripheral...
hello Nordic
i work with nrf52840, SDK16.0 S140
i use QSPI for writing to an external flash (IS25LP064A)
if i write 16 bytes then its all ok but if i try to write...
Hello,
I have nrf52810 with soft device S132 5.1, SDK 14.2.
It works fine when NRF_LOG_ENABLED is enabled, data from NUS are printed in debug console. But Im not able...
Hello,
I am writing a BLE central application that connects to a device and should then discover ALL services on the device. I am new to Nordic and am using the nRF5340...
Hi
I am going to start an application with the mesh network. Here is my requirement,
1. I have to receive the data from the master device (STM32) by using SPIS (nRF52840...
Hello,
I am using the ble_app_uart_c_pca10056_s140 example code (SDK v17). This is the NUS BLE central device.
The code is almost unchanged from the example source.
...
I'm quite new to nrf.
These days I'm trying to program power efficient uart data sender over ble.
It receives uart and sends data fine.
The problem is it's not going...
Hello,
Does nRF52833 has support for FreeRTOS in version 16.0.0 of nrF SDK?
Is there any specific example with the softdevice and FreeRTOS?
Thank You,
Vineeth...
When we develop out product, we found it cannot connect to our server. After our check step by step, we found if we comment the code about RAI setting, MQTT service can be...
I wanted to add TWI functionality to the flash fds example and was confused about adding drivers with CMSISwizard. I manually added all the necessary twi drivers based off...
HI
I have got a new nrf5340 DK. I have tested four LEDs and HRM. It's working fine. But when I have tried to upload blinky or hello_world Sample from NCS v1.5.1, I can't...
Hi all,
I have tested successfully the wireless timer syncronization proposed by:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts...
Hello guys.
I recently discovered that you included example codes for OSDP Control Panel (CP) and Peripheral Devices (PDs). In NCS v1.5.1 that I am using, they can be fund...
