hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello,
Is there a particular test Nordic recommends to screen for latent failures in the BLE circuit? If one has access to an Anritsu MT8852B tester with Direct-Test-Mode...
Hi,
I am updating SDK version from 15.0 to 17.0.
In many examples PM_FLASH_BUFFERS was changed from 2 to 4? What is the meaning of this change? We have one peer always...
While exploring documentaion and trying to learn more about the DFU (and bootloader settings), I found info on how to generate the bootloader settings , which also explains...
I want to measure voltages at all 8 channels but when I am enabling all channels its sending the values once only and after that its not sending anything, my requirement is...
Hi,
We are aware that i2s internally includes hardware double buffering to ensure that the audio is continuous.
Is there any way by which we can avoid double buffering...
Hello,
I developed board with NRF9160 chip and I am facing issue with "at_cmd: Failed to open AT socket (err:-12)", i am not able to communicate with modem. It is not...
Hi
Can I not modify the param the radio project example,and let it run on IEEE802.15.4-2006?
and the demo example run on 2.4GHZ?
I modified two params:
NRF_RADIO-...
Hello,
I'm using nRF52480 Dongle. I executed an Erase All from SEGGER Embedded Studio. My project still works but the LEDs are not blinking anymore. The only way I can have...
Hello nRF Team,
we are using nrf51822 for one of our product. We have implemented firmware update functionality using a secure bootloader library.
After loading the soft...
Hi, I want to distinguish whether the USB is connected to a PC or a power adapter.
For my application, FATFS still needs to work when connected to a power adapter, so it...
Hi Nordic,
Why I cannot directly use segger's "Build and Debug" to download file to nrf52832, after I modify some code?
After I use nrfGo Studio first to program the...
Hi, in the past, there has been discussed several times whether a peripheral can advertise even when it is already connected/bonded. It turned out it could be possible, however...
Hi, We are working on multiple product based on different MCUs (nRF52832 and ESP32). We would like to use the same Nordic BLE DFU for both of the products so that we would...
Planning to run Packetcraft LEAUDIO stack on nRF52840-DK. This is for evaluation and later on for some development on top of it.
Will it be supported. or is it must to have...
Hi,
I am trying to figure out how serial handling works. Specific questions bolded below. To the best I can see, what I think happens when transmitting is:
NRF_SERIAL_DRV_UART_CONFIG_DEF...
