Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hi,
I am using nRF52832 S132 SDK15.2
I am developing an application where the development kit which i am programming is a peripheral.
i want this to connect to specific...
Hey All,
I'm running the LTE Link Monitor on nRF Connect 3.3.3. I'm connecting to my custom nR9160 Feather via the built in USB-to-Serial. I'm able to open the serial port...
I tried to drive MAX30003 to get ECG signals through nrf52832.
I use an analog signal instrument to give the standard ECG signals. Now,the nrf's SPI timing sequence is right...
Hello,
The BLE peripheral I'm developing does not have any specific required connection parameters. I understand that the central ultimately controls the selection of parameters...
Dear
I modify the example of PCA10056 mesh light-server for PCA10059 and it works after I program PCA10059 by nRF Connect –programmer go through USB interface. But there...
Hello,
What is the PPM of LFRC?
In our case, the device will remain in low power mode (System ON, wake up from RTC). The device will wake up at every one hour. Which...
Hello Nordic,
nRF52840, SDK16.0, Softdevice 7.0.1.
I'm using LFCLK to generate an accurate tick for device time keeping (with Prescaler=255, Freq=128Hz, Tick=7.8125ms...
Hi all,
I have a problem when I connect the nRF51822 to my phone.
I use the softdevice S130 and the following code attach .
When I use the nRFconnect in my phone, I...
I have a module BL651 and I want to use it in my dev board. I've found in some previous posts that I have to use nrf52 DK to program externally the nrf52810 in my module....
Hi everyone,
I am using nRF52840 to prototype and I want on certain occations to disconnect the peripheral from the central. On of these occations is when I charge my device...
Hi,
I have a mesh network established with one of the nodes being the provisioner. I am currently using Laird BL652. I want to make an android application for the mesh such...
hi support team,
i have one question about 9160 TCP communication, is data re-transmission fulfillment by the modem? how does it work when in psm mode?
for example, when...
Hello All,
I am working on nRF51822 custom board.Use SDK nRF5 12.3.0 in IAR workbench.
I am use ble peripheral example path given below,
...\...\examples\ble_peripheral...
Hi!
I am trying to add service data to my scan response service data for a custom service. I am unsure of how to set the UUID correctly for this.
UUID declaration:
...
After compiling, loading and running the example code for "ble_app_hts", on an nRF52 DK board, I connected to it using the nRF BLE Toolbox app "HTM" on an Android phone. The...
