I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
I'm trying to interface 2 SPH0645 mics to the nRF52840 DK.
Little did I know when I bought them (the mics) that you need to waste 2 timers + 2 pins + memory space to make...
Hi,
I am trying to measure a signal using the SAADC driver on SDK 13. I have used the example from the nrf52 playground for low power ADC
I have a few questions on best...
Hi,
I have a nRF91 development kit and want to connect P4 to the Segger Jtrace for ETM streaming. In the manual, it stated that a 2×10 pin 1.27 mm pitch surface mount connector...
Hi,
Is there any way to get network time without previously setting it with AT+CCLK?
I would like to implement sort of "fake time" by initialising it with the network...
Hi, I'm struggeling with this stage on the "getting started assistant"
"Clone the nRF Connect SDK"
Is there any step by step video to help me do this, I have probably...
I have one service with multiple characteristics(11). Out of 11 characteristics I have 7 characteristics which have notify as their attributes. So when I select the notification...
I have been using nRF9160: LTE Sensor Gateway to send data from nRF52832 to the cloud. The nRF9160 is subscribed to nRF52832 and hence gets updates after every certain period...
Hi,
I'm trying to use Power Profiler Kit (PPK) with nRF52 DK to measure the power consumption of our custom hardware. My setup is as described below: - The PPK is connected...
SDK:15.2
IC:NRF52840
Hi，When I upgraded the device using usb dfu, after entering the app, there will be an additional current of about 180uA（Sometimes appear）.
Both...
Somehow my nRF9160 DK board has become essentially unresponsive. Flashing new modem using nRF Connect Programmer, and downloaded nRF FW, "seem" to work. But nothing else....
The asset_tracker repo now has a file called: prj_nrf9160_pca20035ns.conf
Is this still compatible with the nRF9160 DK that is using pca10090n ?
What does the pcsNNNNNn...
Hello everyone,
im using the nRF52840 DK, softdevice s140 and the ble_app_tamplate example. In this example i can send data through the GATT protocol. But i want to change...
Hi ,
I would like to know if the .dat file inside the DFU packet is always the same or it can be different.
Is it Possible to fix inside the code ?
What is the .dat...
