I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
I am using the BMD-350 in a new device that reads off of a sensor and changes the alert level in the IAS based on the value. Implementing the client on this peripheral, I...
Hi
I'm trying to use the nRF52840 DK debug out to program/flash an external nRF52840 IC that runs at 1.8V logic level. According to the manual, the DK is running at 3V...
When running our hardware using the J-Link debug in connector on the dev kit, BT is fully functional. But when we try to run using the very same power source (ie, the dev...
Hi all,
I'm developing a custom board that is equipped with a nRF24L01+ (directly soldered on my PCB, no breakout). The board is equipped with a PIC32, that controls also...
SDK 15.2
port_cmsis_systick.c
nrf_drv_clock_lfclk_request is part of the legacy drivers that will eventually be removed?
Does this mean for FreeRTOS I need to keep...
Hello,
I want to set the nrf24le1 module into register retention mode with timers ON but clock source from XOSC32K. I need this power saving code in my project. Also can...
Hi,
I am using adafruit Bluefruit BLE SNIFFER. My question is whether it is required to use jLink along with it to connect to it via USB. Also, I have a question can I sniff...
sdk5 15.2's app_timer.h at line 61 says:
* @details Use the USE_SCHEDULER parameter of the APP_TIMER_INIT() macro to select if the * @ref app_scheduler should be used or...
I am trying to read hts221 and ccs811 sensors from thingy and want to make the data available on UART(P0.02,P0.03).
I have tested the uart code and able to print data -...
Hi all,
I am trying to configure the LPCOMP module of the nrf52832 using registers directly, that is, without using the already generic functions that come with the sde...
Hello
I have two similar (as their producer says) boards. Both nRF52832. The main difference is in modems used for external data transmission.
SDK 15.0.0
SD 132
I...
I have an application using mesh SDK 2.1.1 that is working. I am migrating to V2.2.0. In my current code I use nrf_mesh_opt_set() to enable and disable a relay feature. I...
Hi,
Can nRF Sniffer v2.x software flashed in nRF52832 used along with wireshark sniff all BT 4.0,4.1,4.2,5.0 packets?
Please confirm so that we can proceed to buy the...
Hi there,
The DFU Nordic samples have a 4K "MBR Params" page, located in the last 4K of flash. e.g., the linker file has:
MBR_PARAMS_PAGE (rw) : ORIGIN = 0x0007E000...
Hi,
I need to minimize the power consumption.
For this reason when my device is in advertising the peripherals:
TWI
hight frequency clock
external interrupt on...
