Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
I'm trying to perform a DFU firmware update via command line using nrfutil dfu ble.
The same update using nRF connect works fine. The dongle is flashed with connectivity_1...
I would like to have a ZigBee stack running on the 52840 and use door/window (contact) sensors as well as motion (PIR) that are available on the market today to connect to...
Dear Sirs!
I use compiler IAR 7.80 with Nordic SDK 12.2
Softdevice
s132_nrf52_3.0.0_softdevice.hex
I have very strange issue in debugger.
Break point works, but...
Hi folks,
I try change blinky code for nRF52810 SoC. I must create own timer. I dont know app_timer example help for me?! I want to do when power on leds on 2 seconds...
Hi All,
I am developing an application in which i am interfacing the nRF52832 with an ADC via SPI.
I am doing channel multiplexing (2 channels) such that when i get data...
I'm aware of the limitations on using "printf" in a non-debug environment, but apparently there must be something similar with sprintf. I'm using it to load a value into a...
Hello,
There's a problem compiling the standard ble_app_uart_pca10040_s132 in Segger Embedded Studio for ARM V3.40. The UART example is straight out of nRF5_SDK_14.2.0_17b948a...
Based on the demonstration video of Thingy , I can have a view on Thingy is changing its color when it is given different command using the apps.
1. As if I want to send...
Hello, I want to include Mesh Serial Example into the Mesh Light Switch example.
The aim is to allow the serial device to listen to the mesh messages.
What is the best...
Hi Everyone
I am using BLE for NORDIC UART SERVICES. I want to update my code via BLE instead of a USB or J-LINK.
How can i upload my code from the Android device to nrf52840...
Hi,
I am working on nRF52840 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
I am trying to bring up UART on my custom board.
So as a first...
I followed test steps mentioned in dfu_quick_start.md file to perform DFU over mesh.
1. Below is the error i am getting while creating DFU package, Please help on this....
Hi,
I am working on nRF52832 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
I am trying to erase page from RAM using "nrf_nvmc_page_erase...
I have a situation with the devices my company builds. From what I understand, they've been designed with a small flaw, which causes them to sometimes get stuck and require...
