Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
HI:
It is correct that call the function nrf_nvmc_write_word at nrf51_sdk_v4_4_2 and s110_nrf51822_5.2.1。
void FlashWRPProcess(void)
{
#define NRF_UICR_RBPCONF_ADDRESS...
S110 define UUID rule as below, it just can modify one word.
Services UUID = 0x49535343-FE7D-4AE5-8FA9-9FAFD2-5E455
Characteristics UUID= 0x49530001-FE7D-4AE5-8FA9-9FAFD2...
I have programmed custom services on my evaluation kit and everything works great. I am now looking to implement updating my application from iOS and Android app.
Using...
Hi,
i have a question relative to the configuration tool File Format.
I'd like to modify (automatically) the configuration file in order to change the "Device Name"...
I am using a Bluetooth NRF 8001 module. I want to send data to the module from my android phone to the bluetooth module connected to an Arduino. For sample test I used nrf...
Dear Håkon Alseth,
you posted twi source code which took care of all SD/PPI stuff here and it was also linked here , but it is no longer available. The whole forum seams...
Hello,
I use the bootloader in SDK v5.2.0 and could not run APP after DFU completed.
It always stay in the DFU state.
After checking the memory by J-Link commander, something...
At work we are primarily interested in using the 128kb nRF51822 devices. I am able to get a softdevice and bootloader onto a 256kb device just fine. When I attempt to do the...
Hello all,
I want to send some sensor data( collected by Pic controller) to other BLE client(may be a phone) using nrf51822 via UART. Can somebody suggest how to communicate...
Hi,
In the reference design of "nRF51822-QFAA_ST_BAL-NRF01D3", the datasheet recommends this crystal ( www.digikey.com/.../3125558) , but we are out of stock from local...
Hello all,
I have flased "ble_app_hts" example for nrf51822 on evaluation board PCA10001. In the application both the LED pins are configured for output using "nrf_gpio_cfg_output...
I have a large array of uint16_t data to use as a lookup table, which is defined in flash. It's 4002 bytes in size, and I can set where in flash it is saved. I'm accessing...
I am using an nRF51422 and attempting to interface
it with an MPU9150/6050 using your MPU6050 driver and
the underlying twi_hw_master.c.
I have modified twi_master_config...
Hi all,
My application gathers sensor data and uses the advertisement packet to broadcast the values (much the same as the nordic temp sensor example). Rather than having...
