I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi,
In my application I need accurate calendar capabilities such as alerts on every hour and alert on a specific hour every day. Is there any implementation of such a mode...
Hi,
Want to read data from HX711 adc amplifer with wheatstone bridge loadcells, but when i run the program, my output is <info> app: ADC measuremement -8388608 all the time...
I'm a little confused by the packet rate I'm getting on Gazell. Or rather I'm confused by the low number of 'timeouts' I'm seeing - I'd expect to see more, and would like...
Hi all,
in my custom board I'm using an NRF24L01+ as RF transceiver. The relevant part of schematic follow: (hi res => https://imgur.com/a/z4nQxXh )
The following...
The nRF905 chip can be setup to different payload length. 0-31 byte
Must RX and TX unit be setup to same payload length or can RX unit be setup to ex. 20 bytes and TX unit...
Hello.
There is a label on the back of the nRF9160DK.
I can find "HWID: FF:6A:B3:34:69:AC" on the label.
nRF connect can get the same string: " FF:6A:B3:34:69:AC " when...
I am trying eddystone example from SDK 15, its working fine but once I press the button to enable connecting and function nrf_ble_es_on_start_connectable_advertising(); is...
I want to use REG0 to supply 1.8v to external 4.7k pull-ups including when the system is off. Looking at the product specification REG0 can supply 1mA while in system off...
I have updated my repos to the latest commits on master for zephyr, mcuboot, nrf, and nrfxlib. I ran `
pip3 install -r scripts\requirements.txt
and I can open the asset_tracker...
hi, I'm working with NRF52832, DFU service is configured as secured. my question is : i'm trying to change dfu char a ct e ristic property to "ind i cation" by writing to...
Hello
I would like to test if provisioning over GATT Bearer still works with our application. Firstly I thought of using the serial example together with the PyACI, but...
Hardware: nRF52832
SDK 14.2
Segger Studio
Hello Sir or Madam,
We've made a new hardware variant of a previous design with an nRF52832 on much smaller form factor...
I use the QSPI(SDK15.2) of NRF52840 to read and write FLASH. Every time I open QSPI function, QSPI is closed after writing flash, but after close QSPI, there will be occasional...
Hi,
I want to capture data from TWI ADXL345 and send them by ble_nus_data_send() to mobile. Timing of data sending is done by application timer. My problem is that when...
