If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Hi
I've been having issues with this since the first time I installed VS Code and ncs for VS Code. I've used the Nordic's official YT setup guide while installing.
The...
I am not able to flash nrf5340 using seggar embedded stdio and nrf connect .... nothing seems to be working!
I am attaching the log file
nrfjprog version : 10.13.0
JlinkARM...
I am new to NRF chips and trying to read, write, and erase to flash using nrf_fstorage. I have looked at the example project flash_fstorage and I am able to successfully read...
Hi All,
I'm trying to generate an interrupt on the X PWM's falling edge. My idea was to setup the PWM and count the number of falling edges using PPI & a timer / counter...
I have following code fragment to enter nRF52 into power-off mode. There is s132 softdevice 3.0.0 running and my SDK is 12.0.0:
int32_t ret = sd_power_system_off();
...
Hello,
I am having an issue viewing serial communication from the nRF9160 on the LTE link monitor. I am able to view output when the code is compiled from a different...
After burning the application, the following operations were performed: nrfjprog.exe -f NRF52 --rbp ALL nrfjprog.exe -f NRF52 --pinreset
There are a total of 600 devices...
Hi everyone,
I have setup a Bluetooth Mesh network of 5 Light Control Server Nodes and 5 Low Power Nodes that have friendship with eachother.
All nodes publish and subscribe...
I'm facing the requirement to save few kb of data in flash and process it over time. Because none of the standard mesh models fit, a custom mesh model will be the only option...
Hey,
I encountered a very strange problem while I was trying to connect from nRF52832 (as a central device) to my nRF52805 as a peripheral. If I am trying to connect to...
Hello,
I am working on a custom development board that is using the nRF52840. After programming the nRF52840 on the board with Soft Device s140_nrf52_7.0.1_softdevice.hex...
Hello DevZone,
A product I use uses NFC tag type 2 to communicate. It usually communicates to a separate chip but I want to replace this with the nRF52832.
I opened...
Hello,
I'm working on a product where we want the nRF52840 to be able to reset itself in hardware . This is currently done via an IO that drives a SHUTDOWN# signal into...
Hi,
I'm using TWI to control accemeter(MMA452).When I used TWI SENSOR to read my sensor, it didn't work normally.
The address of MMA8452 is 0x1C,so i want to read...
