I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
First time I programmed the BMD 300 IC ,it got programmed and worked good.After some days later I tried program the board, But the previous code was present in the mcu, i...
When using nrfutil to upgrade the app for 52840dongle, you can see the data shown in the figure through the USB analyzer. The highlighted one does not quite understand the...
Hello,
I'm working on an nRF52832 with SoftDevice v6.1.0 and SDK 15.3.0. We have made a custom application that was created from the ble_app_uart example project. We've...
I inserted code.
OUT 0x04 endpoint works, but 0x84 IN endpoint doesn't.
I use libusb from Linux PC to communicate with nrf52840 via USB. At PC I call function "libusb_bulk_transfer...
I am not able to find the schematics of the development board.
The info center redirects me to the download page of the nRF52840-DK but there are no schematics in the drop...
Hi,
I was wondering if you could give me information on the validity period of the GPS assistance data?
In other words, how often do you need to download the data...
Hello,
I am working developing an application that sends data as notification to connected host at the data rate of 2KB/sec. The chip being used is NRF52832 with S132 soft...
Hello there; My setup: NRF52832 SDK 15.3 I'm facing some problems with FDS when i use it with BLE activated.
When i read or write on FDS using fds_record_open or fds_record_update...
I followed the steps mentioned in the Bluetooth low energy Characteristics, a beginner's tutorial, but at "if ((p_evt_write->handle == p_our_service->characteristic1_value_write_handler...
Hi, I tested "Simple_coap_client" and "simple_coap_server" on NRF52840 using Threading SDK.
I want to change the transmit power, so I used "otPlatRadioSetTransmitPower ...
52810, LIS3DH, I call nrf_drv_twi_tx got NRF_ERROR_DRV_TWI_ERR_ANACK return using either TWI/ or TWIM . Here is my code:
const nrf_drv_twi_config_t config = { .scl = TWI_MASTER_CONFIG_CLOCK_PIN_NUMBER...
Hello,
I want to verify with you if the Standby current for My Bluetooth 5.0 corresponds to the system "on" according to the Bluetooth datasheet or there is another way...
Hello, we've built up quite a bit of experience programming Nordic targets with Keil and nRFgo studio. We love your products. However, we are considering moving away from...
I'm trying to get debug output to appear in my Segger J-LINK SWO viewer (from an NR52840 SDK board with NRF5 v16) which I understand is a potentially complicated process;...
I use Peer Manager for storing bonding infomation with nRF52832 (SDK14.2) using gcc.
I understand Peer Manager uses FDS, and FDS uses flash memory from 0x7D000 to 0x80000...
